- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL9217IRZ (INTERSIL CORP) 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set PDF資料下載
參數資料
| 型號： | ISL9217IRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24 |
| 封裝： | 4 X 4 MM, ROHS COMPLIANT, PLASTIC, QFN-24 |
| 文件頁數： | 24/33頁 |
| 文件大?。?/td> | 645K |
| 代理商： | ISL9217IRZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
24
FN6488.1
November 2, 2007
In the event of an automatic over-temperature condition, cell
balancing is prevented and FETs are held off until the
temperature drops back below the temperature recovery
threshold. During this temperature shutdown period, the
microcontroller can monitor the internal temperature through
the analog output pin (AO), but any writes to the CFET bit,
DFET bit, or cell balancing bits are ignored
The automatic response to an internal over-temperature is
prevented by setting the DISITSD bit to “1”. The automatic
response to an external over-temperature is prevented by
setting the DISXTSD bit to “1”. In either case, it is important
for the microcontroller to monitor the internal and external
temperature to protect the pack and the electronics in an
over-temperature condition.
Analog Multiplexer Selection
The ISL9216 and ISL9217 devices can be used to externally
monitor individual battery cell voltages and temperatures.
Each quantity can be monitored at the analog output pin (AO)
and is selected using the I
2
C interface. See Figure 6.
To monitor the voltages on the ISL9217 inputs, set the
ISL9216 to monitor VCELL6, then set the ISL9217 to the
desired VCELL input. The ISL9216 and ISL9217 VCELL
input voltages are divided by 2, except for the ISL9216
VCELL6 input. This is a divide by 1 input. In this way, the
value read at the ISL9216 AO output is always a divide by 2
of the original cell voltage.
VOLTAGE MONITORING
Since the voltage on each of the Li-Ion Cells are normally
higher than the regulated supply voltage, it is necessary to
both level shift and divide the voltage. To get into the voltage
range required by the external A/D converter, the voltage
level shifter divides the cell voltage by 2. Therefore, a Li-Ion
cell with a voltage of 4.2V is reported via the AO pin to be
2.1V.
TEMPERATURE MONITORING
The voltage representing the external temperature applied at
the TEMPI terminal is directed to the AO terminal through a
MUX, as selected by the AO control bits (see Figures 5
and 6). The external temperature voltage is not divided by 2
as are the cell voltages. Instead it is a direct reflection of the
voltage at the TEMPI pin.
A similar operation occurs when monitoring the internal
temperature through the AO output, except there is no
external “calibration” of the voltage associated with the
internal temperature. For the internal temperature
monitoring, the voltage at the output is linear with respect to
temperature. (See “Operating Specifications” on page 6 for
information about the output voltage at +25°C and the output
slope relative to temperature).
Cell Balancing
OVERVIEW
A typical ISL9216 and ISL9217 Li-ion battery pack consists
of 8 to 12 cells in series, with one or more cells in parallel.
This combination gives both the voltage and power
necessary for power tools, e-bikes, electric wheel chairs,
portable medical equipment, and battery powered industrial
applications. While the series/parallel combination of Li-ion
cells is common, the configuration is not as efficient as it
could be, because any capacity mismatch between series-
connected cells reduces the overall pack capacity. This
mismatch is greater as the number of series cells and the
load current increase. Cell balancing techniques increase
the capacity and the operating time of Li-ion battery packs.
AO
VCELL4
VSS
SCL
SDA
I
2
C
FIGURE 6. ANALOG OUTPUT MONITORING DIAGRAM
REGS
AO3:AO0
DECODE
VCELL1
VCELL5
2
LEVEL
SHIFT
LEVEL
SHIFT
LEVEL
SHIFT
LEVEL
SHIFT
TEMPI
(ISL9216 ONLY)
INT
TEMP
MUX
EXT TEMP.
AO
VCELL2
VSS
I
2
C
REGS
AO3:AO0
DECODE
VCELL1
VCELL6
VC7/VCC
2
LEVEL
SHIFT
LEVEL
SHIFT
LEVEL
SHIFT
LEVEL
SHIFT
INT
TEMP
MUX
VCELL6
1
1
VCC
LEVEL
SHIFT
ISL9216
ISL9217
ISL9216, ISL9217
相關PDF資料 |
PDF描述 |
|---|---|
| ISL95310 | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310WIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310UIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95311 | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
| ISL95311WIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9217IRZ-T | 功能描述:IC MULTI-CELL LI-ION PROT 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9219AIRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219AIRZR5332 | 功能描述:IC BATT CHARGER LI-ION 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219AIRZ-T | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219IRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。