- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL9217IRZ (INTERSIL CORP) 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set PDF資料下載
參數資料
| 型號： | ISL9217IRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24 |
| 封裝： | 4 X 4 MM, ROHS COMPLIANT, PLASTIC, QFN-24 |
| 文件頁數： | 22/33頁 |
| 文件大?。?/td> | 645K |
| 代理商： | ISL9217IRZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
22
FN6488.1
November 2, 2007
OVERCURRENT SAFETY FUNCTIONS
The ISL9216 continually monitors the discharge current by
monitoring the voltage at the CSENSE and DSENSE pins. If
that voltage exceeds a selected value for a time exceeding a
selected delay, then the device enters an overcurrent or short
circuit protection mode. In these modes, the ISL9216
automatically turns off both power FETs and hence prevents
current from flowing through the terminals P+ and P-.
The voltage thresholds and the response times of the
overcurrent protection circuits are selectable for discharge
overcurrent, charge overcurrent, and discharge short circuit
conditions. The specific settings are determined by bits in
the “DISCHARGE SET CONFIGURATION REGISTER
(ADDR: 05H)” on page 18, and “CHARGE/TIME SCALE
CONFIGURATION REGISTER (ADDR: 06H)” on page 19.
(See also “REGISTERS” on page 14).
In an overcurrent condition, the ISL9216 automatically turns off
the voltage on CFET and DFET pins. The DFET output drives
the discharge FET gate low, turning off the FET quickly. The
CFET output turns off and allows the gate of the charge FET to
be pulled low through a resistor.
By turning off the FETs the ISL9216 prevents damage to the
battery pack caused by excessive current into or out of the cells
(as in the case of a faulty charger or short circuit condition).
When the ISL9216 detects a discharge overcurrent condition,
the ISL9216 turns off both power FETs and sets the DOC bit.
(When the FETs are turned off, the DFET and CFET bits are
also reset). The automatic response to overcurrent during
discharge is prevented by setting the DENOCD bit to “1”. The
external microcontroller can turn on the FETs at any time to
recover from this condition, but it would usually turn on the load
monitor function (by setting the LDMONEN bit) and monitor the
LDFAIL bit to detect that the overcurrent condition has been
removed.
When the ISL9216 detects a discharge short circuit condition,
both power FETs are turned off and DSC bit is set. (When the
FETs are turned off, the DFET and CFET bits are also reset).
The automatic response to short circuit during discharge is
prevented by setting the DENSCD bit to “1”. The external
microcontroller can turn on the FETs at any time to recover from
this condition, but it would usually turn on the load monitor
function (by setting the LDMONEN bit) and monitor the LDFAIL
bit to detect that the overcurrent condition has been removed.
When the ISL9216 detects a charge overcurrent condition, both
power FETs are turned off and COC bit is set. (When the FETs
are turned off, the DFET and CFET bits are also reset). The
automatic response to overcurrent during discharge is
prevented by setting the DENOCC bit to “1”. The external
microcontroller can turn on the FETs at any time to recover from
this condition, but it would usually wait to do this until the cell
voltages are not over charged and that the overcurrent
condition has been removed. Or, the microcontroller could wait
until the pack is removed from the charger and then re-
attached.
An alternative method of providing the protection function, if
desired by the designer, is to turn off the automatic safety
response. In this case, the ISL9216 device still monitors the
conditions and sets the status bits, but takes no action in
overcurrent or short circuit conditions. Safety of the pack
depends, instead, on the microcontroller to send commands to
the ISL9216 to turn off the FETs.
To facilitate a microcontroller response to an overcurrent
condition, especially if the microcontroller is in a low power
state, a charge overcurrent flag (COC), a discharge overcurrent
flag (DOC), or the short circuit flag (DSC) being set causes the
ISL9216 TEMP3V output to turn on and pull high. (See
Figure 5). This output can be used as an external interrupt by
the microcontroller to wake-up quickly to handle the overcurrent
condition.
LOAD MONITORING
The load monitor function in the ISL9216 (see Figure 4) is used
primarily to detect that the load has been removed following an
overcurrent or short circuit condition during discharge. This can
be used in a control algorithm to prevent the FETs from turning
on while the overload or short circuit condition remains.
The load monitor can also be used by the microcontroller
algorithms after an undervoltage condition on any cells
causes the FETs to turn off. Use of the load monitor prevents
the FETs from turning on while the load is still present. This
minimizes the possible “oscillations” that can occur when a
load is applied in a low capacity pack. It can also be part of a
system protection mechanism to prevent the load from
turning on automatically - i.e. some action must be taken
before the pack is again turned on.
FIGURE 4. LOAD MONITOR CIRCUIT
VSS
LDMONEN
VMON
V
REF
LDFAIL
=1 if VMON > V
VMONH
=0 if VMON
≤
V
VMONL
ISL9216
P-
VSS
P+
R
L
OPEN
DFET
R
1
36V
ISL9216, ISL9217
相關PDF資料 |
PDF描述 |
|---|---|
| ISL95310 | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310WIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310UIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95311 | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
| ISL95311WIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9217IRZ-T | 功能描述:IC MULTI-CELL LI-ION PROT 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9219AIRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219AIRZR5332 | 功能描述:IC BATT CHARGER LI-ION 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219AIRZ-T | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219IRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。