- 您現在的位置：買賣IC網 > PDF目錄384528 > ISL8502 (Intersil Corporation) 2.5A Synchronous Buck Regulator with Integrated MOSFETs PDF資料下載
參數資料
| 型號： | ISL8502 |
| 廠商： | Intersil Corporation |
| 英文描述： | 2.5A Synchronous Buck Regulator with Integrated MOSFETs |
| 中文描述： | 包2.5a同步降壓穩壓器，集成的MOSFET |
| 文件頁數： | 15/19頁 |
| 文件大?。?/td> | 526K |
| 代理商： | ISL8502 |
15
FN6389.0
January 17, 2007
Shoot-Through Protection
A shoot-through condition occurs when both the upper and
lower MOSFETs are turned on simultaneously, effectively
shorting the input voltage to ground. To protect from a shoot-
through condition, the ISL8502 incorporates specialized
circuitry which insures that the complementary MOSFETs
are not ON simultaneously.
Application Guidelines
Operating Frequency
The ISL8502 can operate at switching frequencies from
500kHz to 1.2MHz. A resistor tied from the FS pin to ground
is used to program the switching frequency through the
following Equation 3.
If the FS pin is left unconnected, the ISL8502 will default to a
500kHz switching frequency.
Output Voltage Selection
The output voltage of the regulator can be programmed via
an external resistor divider that is used to scale the output
voltage relative to the internal reference voltage and feed it
back to the inverting input of the error amplifier. Refer to
Figure 36.
The output voltage programming resistor, R4, will depend on
the value chosen for the feedback resistor and the desired
output voltage of the regulator. The value for the feedback
resistor is typically between 1k
Ω
and 10k
Ω
.
R
OUT
If the output voltage desired is 0.6V, then R4 is left
unpopulated.
Output Capacitor Selection
An output capacitor is required to filter the inductor current and
supply the load transient current. The filtering requirements are
a function of the switching frequency and the ripple current. The
load transient requirements are a function of the slew rate
(di/dt) and the magnitude of the transient load current. These
requirements are generally met with a mix of capacitors and
careful layout.
High frequency capacitors initially supply the transient and slow
the current load rate seen by the bulk capacitors. The bulk filter
capacitor values are generally determined by the ESR
(Effective Series Resistance) and voltage rating requirements
rather than actual capacitance requirements.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements.
The shape of the output voltage waveform during a load
transient that represents the worst case loading conditions will
ultimately determine the number of output capacitors and their
type. When this load transient is applied to the converter, most
of the energy required by the load is initially delivered from the
output capacitors. This is due to the finite amount of time
required for the inductor current to slew up to the level of the
output current required by the load. This phenomenon results in
a temporary dip in the output voltage. At the very edge of the
transient, the Equivalent Series Inductance (ESL) of each
capacitor induces a spike that adds on top of the existing
voltage drop due to the Equivalent Series Resistance (ESR).
After the initial spike, attributable to the ESR and ESL of the
capacitors, the output voltage experiences sag. This sag is a
direct consequence of the amount of capacitance on the output.
During the removal of the same output load, the energy stored
in the inductor is dumped into the output capacitors. This
energy dumping creates a temporary hump in the output
voltage. This hump, as with the sag, can be attributed to the
total amount of capacitance on the output. Figure 35 shows a
typical response to a load transient.
R
T
k
Ω
[
]
OSC
]
------------------------------
=
(EQ. 3)
R
4
0.6V
0.6V
–
×
V
=
(EQ. 4)
FIGURE 35. TYPICAL TRANSIENT RESPONSE
V
OUT
I
OUT
Δ
V
ESL
Δ
V
ESR
Δ
V
SAG
Δ
V
HUMP
I
tran
ISL8502
相關PDF資料 |
PDF描述 |
|---|---|
| ISL8502IRZ | 2.5A Synchronous Buck Regulator with Integrated MOSFETs |
| ISL8560MREP | DC/DC Power Switching Regulator |
| ISL8560 | DC/DC Power Switching Regulator |
| ISL8601 | Single-Phase, PMBus-Enabled PWM Controller with Integrated FET Drivers |
| ISL88031 | Quintuple Voltage Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL8502AEVAL1Z | 功能描述:EVAL BOARD FOR ISL8502 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8502AIRZ | 功能描述:IC REG BUCK SYNC ADJ 2A 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:兩者兼有 輸出數:1 輸出電壓:5V，1 V ~ 10 V 輸入電壓:3.5 V ~ 28 V PWM 型:電流模式 頻率 - 開關:220kHz ~ 1MHz 電流 - 輸出:600mA 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:16-QSOP |
| ISL8502AIRZ-T | 功能描述:IC REG BUCK SYNC ADJ 2A 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:兩者兼有 輸出數:1 輸出電壓:5V，1 V ~ 10 V 輸入電壓:3.5 V ~ 28 V PWM 型:電流模式 頻率 - 開關:220kHz ~ 1MHz 電流 - 輸出:600mA 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:16-QSOP |
| ISL8502AIRZ-TR5194 | 制造商:Intersil Corporation 功能描述:PACHINKO INTEGRATED FET SYNCH BUCK - 4X4 24LD QFN, T&R - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 2A 24QFN |
| ISL8502EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL8502 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。