- 您現在的位置：買賣IC網 > PDF目錄383165 > ISL8102CRZ-T (INTERSIL CORP) Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers PDF資料下載
參數資料
| 型號： | ISL8102CRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| 中文描述： | SWITCHING CONTROLLER, PQCC32 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, PLASTIC, MO-220VHHD-2, MLFP-32 |
| 文件頁數： | 16/27頁 |
| 文件大小： | 711K |
| 代理商： | ISL8102CRZ-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
16
FN9247.0
October 19, 2005
Power Good Signal
The power good pin (PGOOD) is an open-drain logic output
that transitions high when the converter is operating after
soft-start. PGOOD pulls low during shutdown and releases
high after a successful soft-start. PGOOD transitions low
when an undervoltage, overvoltage, or overcurrent condition
is detected or when the controller is disabled by a reset from
ENLL or POR. If after an undervoltage or overvoltage event
occurs the output returns to within under and overvoltage
limits, PGOOD will return high.
Undervoltage Detection
The undervoltage threshold is set at 82% of the REF
voltage. When the output voltage (VSEN-RGND) is below
the undervoltage threshold, PGOOD gets pulled low. No
other action is taken by the controller. PGOOD will return
high if the output voltage rises above 85% of the REF
voltage.
Overvoltage Protection
The ISL8102 constantly monitors the difference between the
VSEN and RGND voltages to detect if an overvoltage event
occurs. During soft-start, while the DAC/REF is ramping up,
the overvoltage trip level is the higher of REF plus 150mV or a
fixed voltage, V
OVP
. The fixed voltage, V
OVP
, is 1.67V. Upon
successful soft-start, the overvoltage trip level is only REF
plus 150mV. OVP releases 50mV below its trip point if it was
“REF plus 150mV” that tripped it, and releases 100mV below
its trip point if it was the fixed voltage, V
OVP
, that tripped it.
Actions are taken by the ISL8102 to protect the load when an
overvoltage condition occurs, until the output voltage falls
back within set limits.
At the inception of an overvoltage event, all LGATE signals
are commanded high, and the PGOOD signal is driven low.
This causes the controller to turn on the lower MOSFETs
and pull the output voltage below a level that might cause
damage to the load. The LGATE outputs remain high until
VDIFF falls to within the overvoltage limits explained above.
The ISL8102 will continue to protect the load in this fashion
as long as the overvoltage condition recurs.
Once an overvoltage condition ends the ISL8102 continues
normal operation and PGOOD returns high.
Pre-POR Overvoltage Protection
Prior to PVCC and VCC exceeding their POR levels, the
ISL8102 is designed to protect the load from any overvoltage
events that may occur. This is accomplished by means of an
internal 10k
resistor tied from PHASE to LGATE, which
turns on the lower MOSFET to control the output voltage
until the overvoltage event ceases or the input power supply
cuts off. For complete protection, the low side MOSFET
should have a gate threshold well below the maximum
voltage rating of the load/microprocessor.
In the event that during normal operation the PVCC or VCC
voltage falls back below the POR threshold, the pre-POR
overvoltage protection circuitry reactivates to protect from
any more pre-POR overvoltage events
Open Sense Line Protection
In the case that either of the remote sense lines, VSEN or
GND, become open, the ISL8102 is designed to detect this
and shut down the controller. This event is detected by
monitoring the voltage on the IREF pin, which is a local
version of V
OUT
sensed at the outputs of the inductors.
If VSEN or RGND become opened, VDIFF falls, causing the
duty cycle to increase and the output voltage on IREF to
increase. If the voltage on IREF exceeds “VDIFF+1V”, the
controller will shut down. Once the voltage on IREF falls
below “VDIFF+1V”, the ISL8102 will restart at the beginning
of soft-start.
Overcurrent Protection
The ISL8102 detects overcurrent events by comparing the
droop voltage, V
DROOP
, to the OCSET voltage, V
OCSET
, as
shown in Figure 13. The droop voltage, set by the external
current sensing circuitry, is proportional to the output current
as shown in Equation 8. A constant 100
μ
A flows through
R
OCSET
, creating the OCSET voltage. When the droop
voltage exceeds the OCSET voltage, the overcurrent
protection circuitry activates. Since the droop voltage is
FIGURE 13. POWER GOOD AND PROTECTION CIRCUITRY
-
+
DAC + 150mV
VSEN
-
+
0.82 x DAC
OV
UV
PGOOD
SOFT-START, FAULT
AND CONTROL LOGIC
-
+
OC
-
+
ISEN
IREF
ISUM
ICOMP
OCSET
R
OCSET
+
-
V
DROOP
V
OCSET
+
-
V
OVP
100μA
ISL8102 INTERNAL CIRCUITRY
-
+
RGND
x1
-
+
+1V
VDIFF
DROOP*
*Connect DROOP to IREF
to disable the Droop feature
ISL8102
相關PDF資料 |
PDF描述 |
|---|---|
| ISL8102IRZ | Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL8102IRZ-T | Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL8102 | Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL8102EVAL1 | Two-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL81387 | ±15kV ESD Protected, Dual Protocol (RS-232/RS-485) Transceivers(±15kV ESD保護，雙協議(RS-232/RS-485)收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL8102EVAL1 | 功能描述:EVAL BOARD 1 FOR ISL8102 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:* 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓撲結構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
| ISL8102IRZ | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL8102IRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL8103 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Three-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL8103CRZ | 功能描述:IC REG CTRLR BUCK PWM VM 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。