- 您現在的位置：買賣IC網 > PDF目錄384525 > ISL6529A (Intersil Corporation) Dual Regulator.Synchronous Rectified Buck PWM and Linear Power Controller PDF資料下載
參數資料
| 型號： | ISL6529A |
| 廠商： | Intersil Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Dual Regulator.Synchronous Rectified Buck PWM and Linear Power Controller |
| 中文描述： | 雙Regulator.Synchronous整流降壓PWM和線性功率控制器 |
| 文件頁數： | 12/15頁 |
| 文件大?。?/td> | 376K |
| 代理商： | ISL6529A |
12
FN9127.1
December 28, 2004
ripple current and the ripple voltage is also a function of the
ripple current. The ripple voltage and current are
approximated by the following equations:
Increasing the value of inductance reduces the output ripple
current and voltage ripple. However, increasing the
inductance value will slow the converter response time to a
load transient.
One of the parameters limiting the converter’s response to a
load transient is the time required to slew the inductor
current. Given a sufficiently fast control loop design, the
ISL6529A will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
interval required to slew the inductor current from an initial
current value to the final current level. During this interval the
difference between the inductor current and the load current
must be supplied by the output capacitor(s). Minimizing the
response time can minimize the output capacitance
required.
The response time to a transient is different for the
application of load and the removal of load. The following
equations give the approximate response time interval for
application and removal of a transient load:
where I
TRAN
is the transient load current step, t
RISE
is the
response time to the application of load, and t
FALL
is the
response time to the removal of load.
With a +3.3V input source, the worst case response time can
be either at the application or removal of load and dependent
upon the output voltage setting. Be sure to check both of
these equations at the minimum and maximum output levels
for the worst case response time.
Input Capacitor Selection
The important parameters for the bulk input capacitors are
the voltage rating and the RMS current rating. For reliable
operation, select bulk input capacitors with voltage and
current ratings above the maximum input voltage and largest
RMS current required by the circuit. The capacitor voltage
rating should be at least 1.25 times greater than the
maximum input voltage and a voltage rating of 1.5 times is a
conservative guideline. The RMS current rating requirement
for the input capacitor of a buck regulator is approximately
1/2 of the summation of the DC load current.
Use a mix of input bypass capacitors to control the voltage
overshoot across the switching MOSFETs. Use ceramic
capacitance for the high frequency decoupling and bulk
capacitors to supply the RMS current. Small ceramic
capacitors can be placed very close to the upper MOSFET
to suppress the voltage induced in the parasitic circuit
impedances. Connect them directly to ground with a via
placed very close to the ceramic capacitor footprint.
For a through-hole design, several aluminum electrolytic
capacitors may be needed. For surface mount designs,
tantalum or special polymer capacitors can be used, but
caution must be exercised with regard to the capacitor surge
current rating. These capacitors must be capable of handling
the surge-current at power-up.
TRANSISTOR SELECTION/CONSIDERATIONS
The ISL6529A requires three external transistors. One
N-Channel MOSFET is used as the upper switch in a
standard buck topology PWM converter. Another MOSFET is
used as the lower synchronous switch. The linear controller
drives the gate of an N-Channel MOS transistor used as the
series pass element. The MOSFET transistors should be
selected based upon r
DS(ON)
, gate supply requirements,
and thermal management considerations.
Upper MOSFET SWITCH Selection
In high-current applications, the MOSFET power dissipation,
package selection and heatsink are the dominant design
factors. The power dissipation includes two loss
components; conduction loss and switching loss. The
conduction losses account for a large portion of the power
dissipation of the upper MOSFET. Switching losses also
contribute to the overall MOSFET power loss.
where I
o
is the maximum load current, D is the duty cycle of
the converter (defined as V
O
/V
IN
), t
SW
is the switching
interval, and F
SW
is the PWM switching frequency.
The lower MOSFET has only conduction loses since it
switches with zero voltage across the device. Conduction
loss is:
These equations assume linear voltage-current transitions
and are approximations. The gate-charge losses are
dissipated by the ISL6529A and do not heat the MOSFET.
However, large gate-charge increases the switching interval,
t
SW
, which increases the upper MOSFET switching losses.
I
V
------F
V
–
S
V
IN
---V
×
=
V
OUT
I
ESR
×
=
(EQ. 11)
(EQ. 12)
t
RISE
L
IN
I
TRAN
V
OUT
×
–
V
=
t
FALL
L
--------V
I
OUT
×
=
(EQ. 13)
(EQ. 14)
P
ConductionUpper
I
o
2
r
DS on
)
×
D
×
P
Switching
1
o
V
IN
×
t
SW
×
F
SW
×
(EQ. 15)
(EQ. 16)
P
ConductionLower
I
o
2
r
DS on
)
×
1
D
–
(
)
×
(EQ. 17)
ISL6529A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6535 | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
| ISL6535CBZ | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
| ISL6535CRZ | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
| ISL6535IBZ | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
| ISL6535IRZ | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6529ACB | 功能描述:IC REG DL BCK/LINEAR 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6529ACB-T | 功能描述:IC REG DL BCK/LINEAR 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6529ACR | 功能描述:IC REG DL BCK/LINEAR SYNC 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6529ACR-T | 功能描述:IC REG DL BCK/LINEAR SYNC 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6529CB | 功能描述:IC REG DL BCK/LINEAR 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。