- 您現在的位置：買賣IC網 > PDF目錄383148 > ISL6443 (Intersil Corporation) 300kHz Dual, 180° Out-of-Phase, Step-Down PWM and Single Linear Controller(兩路300kHz，180°異相，降壓PWM外加一路線性控制器) PDF資料下載
參數資料
| 型號： | ISL6443 |
| 廠商： | Intersil Corporation |
| 英文描述： | 300kHz Dual, 180° Out-of-Phase, Step-Down PWM and Single Linear Controller(兩路300kHz，180°異相，降壓PWM外加一路線性控制器) |
| 中文描述： | 300kHz的雙路，180 °異相，降壓型PWM和線性控制器單（兩路為300kHz，180 °異相，降壓的PWM外加一路線性控制器） |
| 文件頁數： | 16/18頁 |
| 文件大小： | 341K |
| 代理商： | ISL6443 |
16
FN9044.2
August 9, 2006
A large gate-charge increases the switching time, t
SW
,
which increases the upper MOSFET switching losses.
Ensure that both MOSFETs are within their maximum
junction temperature at high ambient temperature by
calculating the temperature rise according to package
thermal-resistance specifications.
Output Capacitor Selection
The output capacitors for each output have unique
requirements. In general, the output capacitors should be
selected to meet the dynamic regulation requirements
including ripple voltage and load transients. Selection of
output capacitors is also dependent on the output inductor,
so some inductor analysis is required to select the output
capacitors.
One of the parameters limiting the converter’s response to a
load transient is the time required for the inductor current to
slew to it’s new level. The ISL6443 will provide either 0% or
71% duty cycle in response to a load transient.
The response time is the time interval required to slew the
inductor current from an initial current value to the load
current level. During this interval the difference between the
inductor current and the transient current level must be
supplied by the output capacitor(s). Minimizing the response
time can minimize the output capacitance required. Also, if
the load transient rise time is slower than the inductor
response time, as in a hard drive or CD drive, it reduces the
requirement on the output capacitor.
The maximum capacitor value required to provide the full,
rising step, transient load current during the response time of
the inductor is:
)
2
IN
where, C
OUT
is the output capacitor(s) required, L
O
is the
output inductor, I
TRAN
is the transient load current step, V
IN
is the input voltage, V
O
is output voltage, and DV
OUT
is the
drop in output voltage allowed during the load transient.
High frequency capacitors initially supply the transient
current and slow the load rate-of-change seen by the bulk
capacitors. The bulk filter capacitor values are generally
determined by the ESR (Equivalent Series Resistance) and
voltage rating requirements as well as actual capacitance
requirements.
The output voltage ripple is due to the inductor ripple current
and the ESR of the output capacitors as defined by:
where, I
L
is calculated in the
Inductor Selection
section.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load
circuitry for specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications at 300kHz for the bulk
capacitors. In most cases, multiple small-case electrolytic
capacitors perform better than a single large-case capacitor.
The stability requirement on the selection of the output
capacitor is that the ‘ESR zero’, f
Z
, be between 1.2kHz and
30kHz. This range is set by an internal, single compensation
zero at 6kHz. The ESR zero can be a factor of five on either
side of the internal zero and still contribute to increased
phase margin of the control loop. Therefore,
In conclusion, the output capacitors must meet three criteria:
1. They must have sufficient bulk capacitance to sustain the
output voltage during a load transient while the output
inductor current is slewing to the value of the load
transient,
2. The ESR must be sufficiently low to meet the desired
output voltage ripple due to the output inductor current,
and
3. The ESR zero should be placed, in a rather large range,
to provide additional phase margin.
The recommended output capacitor value for the ISL6443 is
between 150
μ
F to 680
μ
F, to meet stability criteria with
external compensation. Use of aluminum electrolytic,
POSCAP, or tantalum type capacitors is recommended. Use
of low ESR ceramic capacitors is possible but would take
more rigorous loop analysis to ensure stability.
Output Inductor Selection
The PWM converters require output inductors. The output
inductor is selected to meet the output voltage ripple
requirements. The inductor value determines the converter’s
ripple current and the ripple voltage is a function of the ripple
current and output capacitor(s) ESR. The ripple voltage
expression is given in the capacitor selection section and the
ripple current is approximated by the following equation:
For the ISL6443, Inductor values between 6.4
μ
H to 10
μ
H is
recommended when using the Typical Application
Schematic. Other values can be used but a thorough stability
study should be done.
P
LOWER
I
------------------------------------------------------------------------------
2
(
)
r
(
)
V
IN
V
–
(
)
=
C
OUT
L
(
)
I
O
(
–
DV
OUT
)
----------------------------------------------------------
=
V
RIPPLE
I
L
ESR
(
)
=
C
OUT
Z
)
------------------------------------
=
I
L
V
---------------------------------------------------------
V
S
–
(
)
V
(
)
IN
=
ISL6443
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6444 | Dual PWM Controller with DDR Memory Option for Gateway Applications(帶DDR存儲器選項的網關專用雙PWM控制器) |
| ISL6445 | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ-TK | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6455 | Triple Output Regulator with Single Synchronous Buck and Dual LDO(帶單同步降壓和雙LDO的三路輸出調節器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6443AEVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6443A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6443AIRZ | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| ISL6443AIRZ-TK | 功能描述:IC CTRLR SGL/STP DWN PWM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6443AIVZ | 功能描述:IC CTRLR SGL/STP DWN PWM 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6443AIVZ-TK | 功能描述:IC CTRLR SGL/STP DWN PWM 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。