- 您現在的位置：買賣IC網 > PDF目錄383148 > ISL6443 (Intersil Corporation) 300kHz Dual, 180° Out-of-Phase, Step-Down PWM and Single Linear Controller(兩路300kHz，180°異相，降壓PWM外加一路線性控制器) PDF資料下載
參數資料
| 型號： | ISL6443 |
| 廠商： | Intersil Corporation |
| 英文描述： | 300kHz Dual, 180° Out-of-Phase, Step-Down PWM and Single Linear Controller(兩路300kHz，180°異相，降壓PWM外加一路線性控制器) |
| 中文描述： | 300kHz的雙路，180 °異相，降壓型PWM和線性控制器單（兩路為300kHz，180 °異相，降壓的PWM外加一路線性控制器） |
| 文件頁數： | 11/18頁 |
| 文件大?。?/td> | 341K |
| 代理商： | ISL6443 |
11
FN9044.2
August 9, 2006
Functional Description
General Description
The ISL6443 integrates control circuits for two synchronous
buck converters and one linear controller. The two
synchronous bucks operate out of phase to substantially
reduce the input ripple and thus reduce the input filter
requirements. The chip has four control lines (SS1, SD1,
SS2, and SD2), which provide independent control for each
of the synchronous buck outputs.
The buck PWM controllers employ a free-running frequency
of 300kHz. The current mode control scheme with an input
voltage feed-forward ramp input to the modulator provides
excellent rejection of input voltage variations and provides
simplified loop compensations.
The linear controller can drive either a PNP or PFET to provide
ultra low-dropout regulation with programmable voltages.
Internal 5V Linear Regulator (VCC_5V)
All ISL6443 functions are internally powered from an on-
chip, low dropout 5V regulator. The maximum regulator input
voltage is 24V. Bypass the regulator’s output (VCC_5V) with
a 4.7μF capacitor to ground. The dropout voltage for this
LDO is typically 600mV, so when VCC_5V is greater than
5.6V, VCC_5V is typically 5V. The ISL6443 also employs an
undervoltage lockout circuit that disables both regulators
when VCC_5V falls below 4.4V.
The internal LDO can source over 60mA to supply the IC,
power the low side gate drivers, charge the external boot
capacitor and supply small external loads. When driving
large FETs especially at 300kHz frequency, little or no
regulator current may be available for external loads.
For example, a single large FET with 15nC total gate charge
requires 15nC x 300kHz = 4.5mA. Also, at higher input
voltages with larger FETs, the power dissipation across the
internal 5V will increase. Excessive dissipation across this
regulator must be avoided to prevent junction temperature
rise. Larger FETs can be used with 5V ±10% input
applications. The thermal overload protection circuit will be
triggered, if the VCC_5V output is short circuited. Connect
VCC_5V to V
IN
for 5V ±10% input applications.
Soft-Start Operation
When soft-start is initiated, the voltage on the SS pin of the
enabled PWM channels starts to ramp gradually, due to the
5
μ
A current sourced into the external capacitor. The output
voltage follows the soft-start voltage.
When the SS pin voltage reaches 0.8V, the output voltage of
the enabled PWM channel reaches the regulation point, and
the soft-start pin voltage continues to rise. At this point the
PGOOD and fault circuitry is enabled. This completes the
soft-start sequence. Any further rise of SS pin voltage does
not affect the output voltage. By varying the values of the
soft-start capacitors, it is possible to provide sequencing of the
main outputs at start-up. The soft-start time can be obtained
from the following equation:
C
A
The soft-start capacitors can be chosen to provide startup
tracking for the two PWM outputs. This can be achieved by
choosing the soft-start capacitors such that the soft-start
capacitor ration equals the respective PWM output voltage
ratio. For example, if I use PWM1 = 1.2V and PWM2 = 3.3V
then the soft-start capacitor ratio should be, C
SS1
/C
SS1
=
1.2/3.3 = 0.364. Figure 14 shows that soft-start waveform
with C
SS1
= 0.01μF and C
SS2
= 0.027μF.
Output Voltage Programming
A resistive divider from the output to ground sets the output
voltage of either PWM channel. The center point of the
divider shall be connected to FBx pin. The output voltage
value is determined by the following equation.
where R1 is the top resistor of the feedback divider network
and R2 is the resistor connected from FBx to ground.
T
SOFT
0.8V
-----------
=
FIGURE 13. SOFT-START OPERATION
VCC_5V
1V/DIV
SS1
1V/DIV
V
OUT1
1V/DIV
FIGURE 14. PWM1 AND PWM2 OUTPUT TRACKING DURING
STARTUP
V
OUT1
1V/DIV
V
OUT2
1V/DIV
V
OUTx
0.8VR1
R2
+
R2
=
ISL6443
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6444 | Dual PWM Controller with DDR Memory Option for Gateway Applications(帶DDR存儲器選項的網關專用雙PWM控制器) |
| ISL6445 | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ-TK | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6455 | Triple Output Regulator with Single Synchronous Buck and Dual LDO(帶單同步降壓和雙LDO的三路輸出調節器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6443AEVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6443A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6443AIRZ | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| ISL6443AIRZ-TK | 功能描述:IC CTRLR SGL/STP DWN PWM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6443AIVZ | 功能描述:IC CTRLR SGL/STP DWN PWM 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6443AIVZ-TK | 功能描述:IC CTRLR SGL/STP DWN PWM 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。