- 您現在的位置：買賣IC網 > PDF目錄383142 > ISL6219CA (INTERSIL CORP) DB50 FEMALE SOLDER SHELL PDF資料下載
參數資料
| 型號： | ISL6219CA |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | DB50 FEMALE SOLDER SHELL |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | PLASTIC, SSOP-28 |
| 文件頁數： | 4/17頁 |
| 文件大小： | 476K |
| 代理商： | ISL6219CA |
4
Functional Pin Descriptions
VID0, VID1, VID2, VID3, VID4 (Pins 1, 2, 3, 4, 5)
These are the inputs to the internal DAC that provide the
reference voltage for output regulation. Each pin has an
internal 20
μ
A pull-up current source to 2.5V making the parts
compatible with CMOS and TTL logic from 5V down to 2.5V.
When a VID change is detected the reference voltage slowly
ramps up or down to the new value in 25mV steps. Connect
these pins to either open-drain or active-pull-up type outputs.
Pulling these pins above 2.9V can cause a reference offset
inaccuracy.
FSET/EN (Pin 7)
This pin has two functions. A resistor placed from FS to
ground sets the switching frequency. There is an inverse
relationship between the value of the resistor and the
switching frequency. This pin can also be used to enable the
IC. See Figure 8
for details.
FB (Pin 8) and COMP (Pin 9)
The internal error amplifier’s inverting input and output
respectively. These pins are connected to an external R-C
network to compensate the regulator.
GND (Pin 14)
Return for VCC and signal ground for the IC.
VSEN (Pin 15)
Power good monitor input. Connect to the microprocessor-
CORE voltage.
PWM3, PWM2, PWM1 (Pins 18, 21, 22)
Pulse-width modulation outputs. These logic outputs tell the
driver IC(s) when to turn the MOSFETs on and off.
ISEN3, ISEN2, ISEN1 (PINS 19, 20, 23)
Current sense inputs. A resistor connected between these
pins and the respective phase nodes has a current
proportional to the current in the lower MOSFET during its
conduction interval. The current is used as a reference for
channel balancing, load sharing, protection, and load-line
regulation.
PGOOD (Pin 25)
Power good. This pin is an open-drain logic signal that
indicates when the microprocessor CORE voltage (VSEN
pin) is within specified limits and soft-start has timed out.
VCC (Pin 28)
Bias supply voltage for the controller. Connect this pin to a
5V power supply.
ISL6219
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6223CA-T | Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| ISL6223CA | Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| ISL6223 | Octal D-Type Edge-Triggered Flip-Flops With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6223EVAL1 | Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| ISL6223EVAL2 | Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6219CA-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6220DWF2E WAF | 制造商:Harris Corporation 功能描述: |
| ISL6223 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| ISL6223CA | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| ISL6223CA-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。