- 您現在的位置：買賣IC網 > PDF目錄9899 > ISL43485IBZ-T (Intersil)IC TXRX 1TX/1RX 3V RS-485 8-SOIC PDF資料下載
參數資料
| 型號： | ISL43485IBZ-T |
| 廠商： | Intersil |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX 1TX/1RX 3V RS-485 8-SOIC |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS422，RS485 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOICN |
| 包裝： | 帶卷 (TR) |
8
FN6071.1
March 15, 2005
Driver Features
The RS-485, RS-422 driver is a differential output device
that delivers at least 1.5V across a 54
load (RS-485), and
at least 2V across a 100
load (RS-422) even with
VCC = 3V. The driver features low propagation delay skew to
maximize bit width, and to minimize EMI, and it is tri-statable
via the active high DE input.
Outputs of the ISL43485 driver are not slew rate limited, so
faster output transition times allow data rates of at least
30Mbps.
Data Rate, Cables, and Terminations
Twisted pair is the cable of choice for RS-485, RS-422
networks. Twisted pair cables tend to pick up noise and
other electromagnetically induced voltages as common
mode signals, which are effectively rejected by the
differential receivers in this IC.
RS-485, RS-422 are intended for network lengths up to
4000’, but the maximum system data rate decreases as the
transmission length increases. Devices operating at 30Mbps
are often limited to lengths of less than one hundred feet.
Figure 6 details the ISL43485’s 30Mbps performance driving
200’ of “CAT5” cable terminated in 120
at both ends. Note
that the differential signal delivered to the receiver at the end
of the cable (A-B) still exceeds 1.5V peak. Longer cable
lengths are possible by reducing the data rate, as shown in
Figure 7 for a data rate of 20Mbps.
To minimize reflections, proper termination is imperative
when using this 30Mbps device. In point-to-point, or point-to-
multipoint (single driver on bus) networks, the main cable
should be terminated in its characteristic impedance
(typically 120
) at the end farthest from the driver. In multi-
receiver applications, stubs connecting receivers to the main
cable should be kept as short as possible. Multipoint (multi-
driver) systems require that the main cable be terminated in
its characteristic impedance at both ends. Stubs connecting
a transceiver to the main cable should be kept as short as
possible.
Built-In Driver Overload Protection
As stated previously, the RS-485 spec requires that drivers
survive worst case bus contentions undamaged. The
ISL43485 meets this requirement via driver output short
circuit current limits, and on-chip thermal shutdown circuitry.
The driver output stages incorporate short circuit current
limiting circuitry which ensures that the output current never
exceeds the RS-485 spec, even at the common mode
voltage range extremes. Additionally, it utilizes a foldback
circuit which reduces the short circuit current, and thus the
power dissipation, whenever the contending voltage
exceeds either supply.
In the event of a major short circuit condition, this device
also includes a thermal shutdown feature that disables the
drivers whenever the die temperature becomes excessive.
This eliminates the power dissipation, allowing the die to
cool. The drivers automatically reenable after the die
temperature drops about 15 degrees. If the contention
persists, the thermal shutdown/reenable cycle repeats until
the fault is cleared. Receivers stay operational during
thermal shutdown.
Low Power Shutdown Mode
This BiCMOS transceiver uses a fraction of the power
required by its bipolar counterparts, nevertheless, the
ISL43485 includes a shutdown feature that reduces the
already low quiescent ICC to a 15nA trickle. They enter
shutdown whenever the receiver and driver are
simultaneously disabled (RE =VCC and DE = GND) for a
period of at least 300ns. Disabling both the driver and the
receiver for less than 80ns guarantees that shutdown is not
entered.
Note that receiver and driver enable times increase when
these devices enable from shutdown. Refer to Notes 5-9, at
the end of the Electrical Specification table, for more
information.
ISL43485
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1203BEAP+T | IC ADC 12BIT 8CH 20-SSOP |
| MAX1080BCUP+ | IC ADC 10BIT 400KSPS 20-TSSOP |
| ISL32374EIBZ | IC XMITTER ESD RS422 LP 16-SOIC |
| IDT72V2111L10PFG8 | IC FIFO SS 512X9 10NS 64QFP |
| MAX11047ECB+T | IC ADC 16BIT PAR 250KSPS 64TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL43640 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, 4 to 1 Multiplexer, High Performance Analog Switch |
| ISL43640_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, 4 to 1 Multiplexer, High Performance Analog Switch |
| ISL43640IR | 功能描述:IC MUX/DEMUX 4X1 16QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| ISL43640IR-T | 功能描述:IC MUX/DEMUX 4X1 16QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| ISL43640IRZ | 功能描述:IC MUX/DEMUX 4X1 16QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:1 系列:- 功能:開關 電路:2 x SPST - NC/NO 導通狀態電阻:8 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.3 V ~ 4.3 V 電流 - 電源:1µA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-UFQFN 供應商設備封裝:8-迷你型QFN（1.4x1.4） 包裝:剪切帶 (CT) 其它名稱:DG2738DN-T1-E4CT |
發布緊急采購，3分鐘左右您將得到回復。