- 您現在的位置：買賣IC網 > PDF目錄9258 > ISL22317TFRTZ-TK (Intersil)IC POT DGTL 128TP LN LP 10-TDFN PDF資料下載
參數資料
| 型號： | ISL22317TFRTZ-TK |
| 廠商： | Intersil |
| 文件頁數： | 4/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 128TP LN LP 10-TDFN |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±10 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-TDFN-EP（3x3） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
12
FN6912.1
April 15, 2010
non-precision DCP by setting this bit to 1. Default value of
the Precision Off bit is 0, i.e. matching to external resistor is
ON.
Note, if the external resistor between REF_A/REF_B is not
populated, the DCP will work as a normal DCP without
giving 99% precision and with ~40% higher value of the
resistance. It is highly recommended to use the bit option
(MSR<6>) to turn OFF the precision mode first and then
removing the external resistor.
All other bits MSR<5:0> are reserved and cannot be written.
Any value read from these bits should be ignored.
I2C Serial Interface
The ISL22317 supports an I2C bi-directional bus oriented
protocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as the
receiver. The device controlling the transfer is a master and
the device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, the ISL22317
operates as a slave device in all applications.
All communication over the I2C interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line must change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (see
Figure 21). On power-up of the ISL22317, the SDA pin is in
the input mode.
All I2C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The ISL22317 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met (see
Figure 21). A START condition is ignored during the
power-up of the device.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH (see Figure 21). A STOP condition at the end
of a read operation, or at the end of a write operation, places
the device in its standby mode.
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (see Figure 22).
The ISL22317 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL22317 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation
A valid Identification Byte contains 01010 as the five MSBs,
and the following bit matching the logic value present at pin
A1. The LSB is the Read/Write bit. Its value is “1” for a Read
operation, and “0” for a Write operation (See Table 4).
TABLE 4. IDENTIFICATION BYTE FORMAT
01010
A1
0
R/W
(MSB)
(LSB)
Logic value at pin A1
SDA
SCL
START
DATA
STOP
STABLE
CHANGE
DATA
STABLE
FIGURE 21. VALID DATA CHANGES, START, AND STOP CONDITIONS
ISL22317
相關PDF資料 |
PDF描述 |
|---|---|
| M83723/72R22128 | CONN RCPT 12POS WALL MT W/PINS |
| M83723/72R22127 | CONN RCPT 12POS WALL MT W/PINS |
| M83723/72R22126 | CONN RCPT 12POS WALL MT W/PINS |
| MS27484T16A6PA | CONN PLUG 6POS STRAIGHT W/PINS |
| MS27474T20B2PA | CONN RCPT 65POS JAM NUT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22317UFRTZ | 功能描述:數字電位計 IC 128 TAP FL RNG PRECISION 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22317UFRTZ-TK | 功能描述:數字電位計 IC 128 TAP FL RNG PRECISION 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22317UFRTZTKS2568 | 制造商:Intersil Corporation 功能描述:INTEL, ISL22317UFRTZ-TK W/BARCODE LABELS, 12 MONTH D/C RESTR - Tape and Reel |
| ISL22317WFRTZ | 功能描述:數字電位計 IC 128 TAP FL RNG PRECISION 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22317WFRTZ-TK | 功能描述:數字電位計 IC 128 TAP FL RNG PRECISION 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。