- 您現在的位置：買賣IC網 > PDF目錄384519 > ISL1209IU10-TK (INTERSIL CORP) Low Power RTC with Battery Backed SRAM and Event Detection PDF資料下載
參數資料
| 型號： | ISL1209IU10-TK |
| 廠商： | INTERSIL CORP |
| 元件分類： | XO, clock |
| 英文描述： | Low Power RTC with Battery Backed SRAM and Event Detection |
| 中文描述： | REAL TIME CLOCK, PDSO8 |
| 封裝： | PLASTIC, MO-187BA, MSOP-8 |
| 文件頁數： | 17/24頁 |
| 文件大小： | 416K |
| 代理商： | ISL1209IU10-TK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
17
FN6109.1
September 27, 2005
Once the registers are set, the following waveform will be
seen at IRQ-:
Note that the status register ALM bit will be set each time the
alarm is triggered, but does not need to be read or cleared.
User Registers
Addresses [12h to 13h]
These registers are 2 bytes of battery-backed user memory
storage.
I
2
C Serial Interface
The ISL1209 supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter and the receiving device as the receiver.
The device controlling the transfer is the master and the
device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, the ISL1209
operates as a slave device in all applications.
All communication over the I
2
C interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (See
Figure 12). On power up of the ISL1209, the SDA pin is in
the input mode.
All I
2
C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The ISL1209 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met (See
Figure 12). A START condition is ignored during the power-
up sequence.
All I
2
C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH (See Figure 12). A STOP condition at the end
of a read operation or at the end of a write operation to
memory only places the device in its standby mode.
An acknowledge (ACK) is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (See Figure 13).
The ISL1209 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL1209 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
ALARM
REGISTER
BIT
DESCRIPTION
7 6 5 4 3 2 1 0 HEX
SCA
1 0 1 1 0 0 0 0 B0h Seconds set to 30,
enabled
MNA
0 0 0 0 0 0 0 0
00h Minutes disabled
HRA
0 0 0 0 0 0 0 0
00h Hours disabled
DTA
0 0 0 0 0 0 0 0
00h Date disabled
MOA
0 0 0 0 0 0 0 0
00h Month disabled
DWA
0 0 0 0 0 0 0 0
00h Day of week disabled
CONTROL
REGISTER
BIT
DESCRIPTION
7 6 5 4 3 2 1 0 HEX
INT
1 1 x x 0 0 0 0
x0h Enable Alarm and Int
Mode
60 sec
RTC and alarm registers are both “30” sec
ISL1209
相關PDF資料 |
PDF描述 |
|---|---|
| ISL1209IU10Z | Low Power RTC with Battery Backed SRAM and Event Detection |
| ISL22416 | Low Noise, Low Power, SPI Bus, 128 Taps(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| ISL22419 | Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| ISL22426 | Low Noise, Low Power, SPI Bus, 128 Taps(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| ISL22429 | Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only(低噪聲,低功率，SPI總線, 128抽頭電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL1209IU10Z | 功能描述:實時時鐘 I2CAL TIME CLK/CLNDR W/EVENT DETCT 10LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1209IU10Z-TK | 功能描述:實時時鐘 I2CAL TIME CLK/CLNDR W/EVENT DETCT 10LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1218 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM |
| ISL1218IBZ | 功能描述:實時時鐘 REAL TIME CLKRTC IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1218IBZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。