11 FN6659.3 November 22, 2011 Brownout Detection The ISL12022 monitors the VDD
參數資料
型號： ISL12022IBZ
廠商： Intersil
文件頁數： 3/29頁
文件大?。?/td> 0K
描述： IC RTC/CALENDAR TEMP SNSR 8-SOIC
應用說明： Addressing Power Issues in Real Time Clock Appls
產品培訓模塊： Solutions for Industrial Control Applications
標準包裝： 98
類型： 時鐘/日歷
特點： 警報器，夏令時，閏年，SRAM
存儲容量： 128B
時間格式： HH:MM:SS（12/24 小時）
數據格式： YY-MM-DD-dd
接口： I²C，2 線串口
電源電壓： 2.7 V ~ 5.5 V
電壓 - 電源，電池： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SOIC
包裝： 管件
產品目錄頁面： 1245 (CN2011-ZH PDF)
ISL12022
11
FN6659.3
November 22, 2011
Brownout Detection
The ISL12022 monitors the VDD level continuously and provides
warning if the VDD level drops below prescribed levels. There are
six (6) levels that can be selected for the trip level. These values
are 85% below popular VDD levels. The LVDD bit in the Status
Register will be set to “1” when brownout is detected. Note that
the I2C serial bus remains active unless the Battery VTRIP levels
are reached.
Battery Level Monitor
The ISL12022 has a built in warning feature once the Back-up
battery level drops first to 85% and then to 75% of the battery’s
nominal VBAT level. When the battery voltage drops to between
85% and 75%, the LBAT85 bit is set in the status register. When
the level drops below 75%, both LBAT85 and LBAT75 bits are set
in the status register.
The battery level monitor is not functional in battery backup
mode. In order to read the monitor bits after powering up VDD,
instigate a battery level measurement by setting the TSE bit to
"1" (BETA register), and then read the bits.
There is a Battery Time Stamp Function available. Once the VDD
is low enough to enable switchover to the battery, the RTC
time/date are written into the TSV2B register. This information
can be read from the TSV2B registers to discover the point in
time of the VDD power-down. If there are multiple power-down
cycles before reading these registers, the first values stored in
these registers will be retained. These registers will hold the
original power-down value until they are cleared by setting CLRTS
= 1 to clear the registers.
The normal power switching of the ISL12022 is designed to
switch into battery-backup mode only if the VDD power is lost.
This will ensure that the device can accept a wide range of
backup voltages from many types of sources while reliably
switching into backup mode.
Note that the ISL12022 is not guaranteed to operate with
VBAT < 1.8V. If the battery voltage is expected to drop lower than
this minimum, correct operation of the device, especially after a
VDD power-down cycle, is not guaranteed.
The minimum VBAT to insure SRAM is stable is 1.0V. Below that,
the SRAM may be corrupted when VDD power resumes.
Real Time Clock Operation
The Real Time Clock (RTC) uses an external 32.768kHz quartz
crystal to maintain an accurate internal representation of
second, minute, hour, day of week, date, month, and year. The
RTC also has leap-year correction. The clock also corrects for
months having fewer than 31 days and has a bit that controls
24-hour or AM/PM format. When the ISL12022 powers up after
the loss of both VDD and VBAT, the clock will not begin
incrementing until at least one byte is written to the clock
register.
Single Event and Interrupt
The alarm mode is enabled via the MSB bit. Choosing single
event or interrupt alarm mode is selected via the IM bit. Note that
when the frequency output function is enabled, the alarm
function is disabled.
The standard alarm allows for alarms of time, date, day of the
week, month, and year. When a time alarm occurs in single
event mode, the IRQ/FOUT pin will be pulled low and the alarm
status bit (ALM) will be set to “1”.
The pulsed interrupt mode allows for repetitive or recurring alarm
functionality. Hence, once the alarm is set, the device will
continue to alarm for each occurring match of the alarm and
present time. Thus, it will alarm as often as every minute (if only
the nth second is set) or as infrequently as once a year (if at least
the nth month is set). During pulsed interrupt mode, the
IRQ/FOUT pin will be pulled low for 250ms and the alarm status
bit (ALM) will be set to “1”.
The ALM bit can be reset by the user or cleared automatically
using the auto reset mode (see ARST bit). The alarm function can
be enabled/disabled during battery-backup mode using the
FOBATB bit. For more information on the alarm, please see
Frequency Output Mode
The ISL12022 has the option to provide a clock output signal
using the IRQ/FOUT open drain output pin. The frequency output
mode is set by using the FO bits to select 15 possible output
frequency values from 1/32Hz to 32kHz. The frequency output
can be enabled/disabled during battery-backup mode using the
FOBATB bit.
General Purpose User SRAM
The ISL12022 provides 128 bytes of user SRAM. The SRAM will
continue to operate in battery-backup mode. However, it should
be noted that the I2C bus is disabled in battery-backup mode.
I2C Serial Interface
The ISL12022 has an I2C serial bus interface that provides
access to the control and status registers and the user SRAM.
The I2C serial interface is compatible with other industry I2C
serial bus protocols using a bi-directional data signal (SDA) and a
clock signal (SCL).
Oscillator Compensation
The ISL12022 provides both initial timing correction and
temperature correction due to variation of the crystal oscillator.
Analog and digital trimming control is provided for initial
adjustment, and a temperature compensation function is
provided to automatically correct for temperature drift of the
crystal. Initial values are preset and recalled on initial power-up
for the Initial AT and DT settings (IATR, IDTR), temperature
coefficient (ALPHA), crystal capacitance (BETA), and the crystal
turn-over temperature (XTO). These initial values are typical of
units available on the market, although the user may program
specific values after testing for best accuracy. The function can
be enabled/disabled at any time and can be used in battery
mode as well.
相關PDF資料
PDF描述
VE-B2L-MY-F4 CONVERTER MOD DC/DC 28V 50W
ISL12027AIV27Z IC RTC/CALENDAR EEPROM 8TSSOP
ISL12026IVZ IC RTC/CALENDAR W/EEPROM 8-TSSOP
VI-JWM-MZ CONVERTER MOD DC/DC 10V 25W
ISL12026IBZ IC RTC/CALENDAR EEPROM 8-SOIC
相關代理商/技術參數
參數描述
ISL12022IBZ-T 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/TEMP COMP 8 L RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12022IBZ-T7A 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/TEMP COMP 8 L RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12022M 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM, Integrated ±5ppm Temperature Compensation, and Auto Daylight Saving
ISL12022M_09 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM, Integrated ±5ppm Temperature Compensation, and Auto Daylight Saving
ISL12022M_10 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM,Integrated ±5ppm Temperature Compensation and Auto Daylight Saving
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*