參數資料
型號： ISD5116EI
廠商： WINBOND ELECTRONICS CORP
元件分類： 音頻合成
英文描述： Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
中文描述： 960 SEC, SPEECH SYNTHESIZER WITH RCDG, PDSO28
封裝： 8 X 13.40 MM, PLASTIC, TSOP1-28
文件頁數： 28/57頁
文件大?。?/td> 735K
代理商： ISD5116EI
Page 27
5 DIGITAL MODE
5.1 WRITING DATA
The Digital Write function allows the user to select a portion of the array to be used as digital
memory. The partition between analog and digital memory is left up to the user. A page can
only be either Digital or Analog, not both. The minimum addressable block of memory in the
digital mode is one block or 64 bits, when reading or writing. The address sent to the device
is the 11-bit row (or page) address with the 5-bit scan (or block) address. However, one must
send a Digital Erase before attempting to change digital data on a page. This means that
even when changing only one of the 32 blocks, all 32 will need to be rewritten to the page.
After the address is entered, the data is sent in one-byte packets followed by an I
C
acknowledge generated by the chip. Data for each block is sent MSB first. The data transfer
is ended when the master generates an I
C STOP condition. If only a partial block of data is
sent before the STOP condition, zero is “written” in the remaining bytes; that is, they are left at
the erase level. An erased page (row) will be read as all zeros. The device can buffer up to
two blocks of data. If the device is unable to accept more data due to the internal write
process, the SCL line will be held LOW indicating to the master to halt data transfer.
If the
device encounters an overflow condition, it will respond by generating an interrupt condition
and an I
C Not Acknowledge signal after the last valid byte of data. Once data transfer is
terminated, the device needs up to two cycles (64 us) to complete its internal write cycle
before another command is sent. If an active command is sent before the internal cycle is
finished, the part will hold SCL LOW until the current command is finished.
5.2 READING DATA
The Digital Read command utilizes the combined I
2
C command format. That is, a command is
sent to the chip using the write data direction. Then the data direction is reversed by sending
a repeated start condition, and the slave address with R/W set to 1. After this, the slave
device (ISD5116) begins to send data to the master until the master generates a Not
Acknowledge. If the part encounters an overflow condition, the INT pin is pulled LOW. No
other communication with the master is possible due to the master generating ACK signals.
As with Digital Write, Digital Read can be done a “block” at a time. Thus, only 64 bits need be
read in each Digital Read command sequence.
5.3 ERASING DATA
The Digital Erase command can only erase an entire page at a time. This means that only the
D1 command needs to include the 11-bit page address; the 5-bit for block address are left at
00000.
Once a page has been erased, each block may be written separately, 64 bits at a time. But, if
a block has been previously written then the entire page of 2048 bits must be erased in order
to re-write (or change) a block.
A sequence might be look like:
- read the entire page
- store it in RAM
- change the desired bit(s)
- erase the page
- write the new data from RAM to the entire page
相關PDF資料
PDF描述
ISD5116P Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISD5116S Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISD5116SD Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISD5116SI Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
ISD5116X Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
相關代理商/技術參數
參數描述
ISD5116EIR 功能描述:IC VOICE REC/PL 8-16MN IN 28TSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116EY 功能描述:IC VOICE REC/PLAY 8-16MN 28-TSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116EYI 功能描述:IC VOICE REC/PLAY 8-16MN 28-TSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116EYR 功能描述:IC VOICE REC/PLAY 8-16MN 28-TSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116P 功能描述:IC VOICE REC/PLAY 8-16MN 28-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*