參數資料
型號： ISD5116
廠商： WINBOND ELECTRONICS CORP
英文描述： Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability
中文描述： 單芯片語音記錄/播放設備與數字存儲能力為16分鐘時間
文件頁數： 31/57頁
文件大?。?/td> 735K
代理商： ISD5116
Page 30
3. Erase digital data
1. Host executes I
2
C START
2. Send Slave Address with R/W bit = “0” (Write)
3. Slave responds back with an ACK
4. Wait for SCL to go HIGH
5. Host sends a byte to Slave - (Command Byte = D1)
6. Slave responds with an ACK
7. Wait for SCL to go HIGH
8. Host sends a byte to Slave - (High Address Byte)
9. Slave responds with an ACK.
10. Wait for SCL to go HIGH
11. Host sends a byte to Slave - (Low Address Byte)
12. Slave responds with an ACK
13. Wait for SCL to go HIGH
14. Host executes I
C STOP
15. Host counts RAC cycles to track where the chip is in the erase operation.
16. Host determines erase of final row has begun
17. Host executes I
C START
18. Send Slave Address with R/W bit = “0” (Write)
19. Slave responds back with an ACK
20. Wait for SCL to go HIGH
21. Host sends a byte to Slave - (Command Byte = 80)
22. Slave responds back with an ACK
23. Wait for SCL to go HIGH
24. Host executes I
C STOP
A
S
SLAVE ADDRESS
W
Command Byte
D1h
A
DATA
A
DATA
A
High Addr. Byte
Low Addr. Byte
A
S
SLAVE ADDRESS
W
P
Command Byte
80h
Erase starts on falling
edge of Slave
acknowledge
Note 2
"N" RAC cycles
Note 3.
Last erased row
Note 4.
A
P
Notes
1. Erase operations must be addressed on a Row boundary. The 5 LSB bits of the Low
Address Byte will be ignored.
2. I2C bus is released while erase proceeds. Other devices may use the bus until it is
time to execute the STOP command that causes the end of the Erase operation.
3. Host processor must count RAC cycles to determine where the chip is in the erase
process, one row per RAC cycle. RAC pulses LOW for 0.25 microsecond at the end
of each erased row. The erase of the "next" row begins with the rising edge of RAC.
See the
Digital Erase RAC timing diagram
on page 32.
4. When the erase of the last desired row begins, the following STOP command
(Command Byte = 80 hex) must be issued. This command must be completely given,
including receiving the ACK from the Slave before the RAC pin goes HIGH .25
microseconds before the end of the row.
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*