- 您現在的位置：買賣IC網 > PDF目錄383120 > ISD-T360SB (Electronic Theatre Controls, Inc.) VoiceDSP Digital Speech Processor with Master/Slave, Full-Duplex Speakerphone, Multiple Flash and ARAM/DRAM Support PDF資料下載
參數資料
| 型號： | ISD-T360SB |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | VoiceDSP Digital Speech Processor with Master/Slave, Full-Duplex Speakerphone, Multiple Flash and ARAM/DRAM Support |
| 中文描述： | VoiceDSP數字語音處理器與主/從，全雙工揚聲器，多重閃光和雅藍/內存支持 |
| 文件頁數： | 47/109頁 |
| 文件大小： | 1567K |
| 代理商： | ISD-T360SB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁
2—SOFTWARE
ISD-T360SB
2-7
ISD
When a command has more than one parame-
ter/return-value, the parameters/return-values
are transmitted in the order of appearance. If a
parameter/return-value is more than one byte
long, the bytes are transmitted from the most sig-
nificant to the least significant.
The MWRDY signal is used as follows:
1.
Active (0) MWRDY signals the microcon-
troller that the last eight bits of data trans-
ferred to/from the voice module were
accepted and processed (see below).
2.
The MWRDY signal is deactivated (set to 1
by the VoiceDSP processor) after 8-bits of
data
were
transferred
VoiceDSP processor. The bit is set follow-
ing the falling edge of the eighth MWCLK
clock-cycle.
to/from
the
3.
The MWRDY signal is activated (cleared to
0) by the VoiceDSP processor when it is
ready to receive the first parameter byte
(if there are any parameters) and so on till
the last byte of parameters is transferred.
An active MWRDY signal after the last
byte of parameters indicates that the
command was parsed and (if possible)
executed. If that command has a return
value, the microcontroller must read the
value before issuing a new command.
4.
When a return value is transmitted, the
MWRDY signal is deactivated after every
byte, and activated again when the
VoiceDSP processor is ready to send an-
other byte, or to receive a new com-
mand.
5.
The MWRDY signal is activated (cleared to
0) after reset, and after a protocol time-
out. (See “INTERFACE PROTOCOL TIME-
OUTS” )
The MWRQST signal is used as follows:
1.
The MWRQST signal is activated (cleared
to 0), when the status word is changed.
2.
The MWRQST signal remains active (0), un-
til the VoiceDSP processor receives a GSW
command.
Figure 1-32 and Figure 1-33 illustrate the se-
quence of activities during a MICROWIRE data
transfer between VoiceDSP and the microcon-
troller.
INTERFACE PROTOCOL TIME-OUTS
Depending on the VoiceDSP processor’s state, if
more than 100 milliseconds elapse between the
assertion of the MWRDY signal and the transmis-
sion 8th bit of the next byte pertaining to the
same command transaction, a time-out event
occurs, and the VoiceDSP processor responds as
follows:
1.
Sets the error bit in the status word to 1.
2.
Sets the EV_TIMEOUT bit in the error word
to 1.
3.
Activates the MWRQST signal (clears it to
0).
4.
Activates the MWRDY signal (clears it to
0).
5.
Waits for a new command. (After a time-
out occurs, i.e., the microcontroller re-
ceived MWRQST during the command
transfer, or result reception, the microcon-
troller must wait at least four milliseconds
before issuing the next command.)
ECHO MECHANISM
The VoiceDSP processor echoes back to the mi-
crocontroller all the bits received by the VoiceD-
SP processor. Upon detection of an error in the
echo, the microcontroller should stop the proto-
col clock, which eventually causes a time-out er-
ror (i.e., ERR_TIMEOUT bit is set in the error word).
NOTE
When a command has a return value, the
VoiceDSP processor transmits bytes of the
return value instead of the echo value.
The VoiceDSP processor transmits a byte as an
echo when it receives the value 0xAA from the
microprocessor. Upon detection of an error the
VoiceDSP processor activates the MWRQST sig-
nal, and sets the ERR_COMM bit in the error
word.
相關PDF資料 |
PDF描述 |
|---|---|
| ISD1000A | Single-Chip Voice Record/Playback Devices 16- and 20-Second Durations |
| ISD1016A | Single-Chip Voice Record/Playback Devices 16- and 20-Second Durations |
| ISD1xxxA | Single-Chip Voice Record/Playback Devices 16- and 20-Second Durations |
| ISD1016AG | Single-Chip Voice Record/Playback Devices 16- and 20-Second Durations |
| ISD1016AGI | Single-Chip Voice Record/Playback Devices 16- and 20-Second Durations |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISD-TH | 制造商:Newport Electronics Inc 功能描述:MONITOR FOR TEMPERATURE HUMIDITY AND DE 制造商:NEWPORT ELECTRONICS 功能描述:MONITOR FOR TEMPERATURE, HUMIDITY AND DE 制造商:Newport Electronics Inc 功能描述:MONITOR FOR TEMPERATURE, HUMIDITY AND DEWPOINT; Input Voltage:100V to 240V; Kit Contents:Monitor (temp + humidity, dewpoint), LCD, 2GB SD, relay alarms, battery backup, 100-240VAC adapter |
| ISD-TH/N | 制造商:Newport Electronics Inc 功能描述:ISD MONITOR FOR TEMPERATURE AND HUMIDITY; Input Voltage:9V to 12V |
| ISD-TH-5 | 制造商:Newport Electronics Inc 功能描述:MONITOR FOR TEMPERATURE AND HUMIDITY 制造商:Newport Electronics Inc 功能描述:MONITOR FOR TEMPERATURE AND HUMIDITY; Input Voltage:100V to 240V; Kit Contents:iSD monitor, LCD display, memory card, relay alarms, battery back-up, pwr adapter. Probe, cable |
| ISD-TH-5/N | 制造商:Newport Electronics Inc 功能描述:ISD MONITOR FOR TEMPERATURE AND HUMIDITY; Input Voltage:9V to 12V |
| ISDTHP | 制造商:Newport Electronics Inc 功能描述:REPLACEMENT RIGHT ANGLE PROBE; Test Probe Functions:Humidity / Temperature; For Use With:Newport Electronics iSD-TH Temperature Humidity Monitor; Kit Contents:Replacement standard right angle probe for iSD-TH product |
發(fā)布緊急采購，3分鐘左右您將得到回復。