參數資料
型號： IQ80C52EXXX-12D
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQFP44
封裝： CERAMIC, QFP-44
文件頁數： 104/108頁
文件大小： 3682K
代理商： IQ80C52EXXX-12D
95
8069R–AVR–06/2013
XMEGA A4
Not recommended for new designs -
Use XMEGA A4U series
Problem fix/Workaround
Keep the amplified voltage output from the ADC gain stage below 2.4 V in order to get a cor-
rect result, or keep ADC voltage reference below 2.4 V.
5.
ADC Event on compare match non-functional
ADC signalling event will be given at every conversion complete even if Interrupt mode (INT-
MODE) is set to BELOW or ABOVE.
Problem fix/Workaround
Enable and use interrupt on compare match when using the compare function.
6.
Bandgap measurement with the ADC is non-functional when VCC is below 2.7V
The ADC can not be used to do bandgap measurements when VCC is below 2.7V.
Problem fix/Workaround
None.
7.
Accuracy lost on first three samples after switching input to ADC gain stage
Due to memory effect in the ADC gain stage, the first three samples after changing input
channel must be disregarded to achieve 12-bit accuracy.
Problem fix/Workaround
Run three ADC conversions and discard these results after changing input channels to ADC
gain stage.
8.
Configuration of PGM and CWCM not as described in XMEGA A Manual
Enabling Common Waveform Channel Mode will enable Pattern generation mode (PGM),
but not Common Waveform Channel Mode.
Enabling Pattern Generation Mode (PGM) and not Common Waveform Channel Mode
(CWCM) will enable both Pattern Generation Mode and Common Waveform Channel Mode.
Problem fix/Workaround
9.
PWM is not restarted properly after a fault in cycle-by-cycle mode
When the AWeX fault restore mode is set to cycle-by-cycle, the waveform output will not
return to normal operation at first update after fault condition is no longer present.
Problem fix/Workaround
Do a write to any AWeX I/O register to re-enable the output.
10. BOD will be enabled after any reset
If any reset source goes active, the BOD will be enabled and keep the device in reset if the
VCC voltage is below the programmed BOD level. During Power-On Reset, reset will not be
released until VCC is above the programmed BOD level even if the BOD is disabled.
Table 36-1.
Configure PWM and CWCM according to this table:
PGM
CWCM
Description
0
PGM and CWCM disabled
0
1
PGM enabled
1
0
PGM and CWCM enabled
1
PGM enabled
相關PDF資料
PDF描述
IP80C32-L16:D 8-BIT, 16 MHz, MICROCONTROLLER, PDIP40
MQ80C52CXXX-25P883 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
R83C154DTXXX-L16D 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44
R83C154DTXXX-25D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
R83C154DTXXX-30R 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CQCC44
相關代理商/技術參數
參數描述
IQ80T B 制造商:Omnimount 功能描述:Tilt Mount for Flat Panel Televisions 23"~42" 80lb. Capacity 制造商:OMNIMOUNT 功能描述:DWO FLAT PANEL MOUNT TILT FOR 23 IN - 42 IN FLAT PANELS
IQ81349SC 888389 制造商:Intel 功能描述:IQ81349SC - Bulk
IQ82C55A 功能描述:IC I/O EXPANDER 24B 44MQFP RoHS:否 類別:集成電路 (IC) >> 接口 - I/O 擴展器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 接口:I²C，JTAG 輸入/輸出數:9 中斷輸出:無 頻率 - 時鐘:400kHz 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 包括:EEPROM
IQ82C55A96 功能描述:IC I/O EXPANDER 24B 44MQFP RoHS:否 類別:集成電路 (IC) >> 接口 - I/O 擴展器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 接口:I²C，JTAG 輸入/輸出數:9 中斷輸出:無 頻率 - 時鐘:400kHz 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 包括:EEPROM
IQ82C55AZ 功能描述:外圍驅動器與原件 - PCI PERI PRG-I/O 5V 8MHZ INDUSTRIAL TEMP RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*