- 您現在的位置：買賣IC網 > PDF目錄9968 > IDT82P2521BH (IDT, Integrated Device Technology Inc)IC LIU E1 21+1CH SHORT 640-PBGA PDF資料下載
參數資料
| 型號： | IDT82P2521BH |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 75/147頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E1 21+1CH SHORT 640-PBGA |
| 標準包裝： | 5 |
| 類型： | 線路接口裝置（LIU） |
| 規程： | E1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 640-BGA 裸露焊盤 |
| 供應商設備封裝： | 640-PBGA-EP（31x31） |
| 包裝： | 托盤 |
| 其它名稱： | 82P2521BH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁
IDT82P2521
21(+1) CHANNEL HIGH-DENSITY E1 LINE INTERFACE UNIT
Functional Description
33
December 7, 2005
3.1.3
SLICER
The Slicer is used to generate a standard amplitude mark or a space
according to the amplitude of the input signals. The input signal is sliced
at 50% of the peak value.
3.1.4
RX CLOCK & DATA RECOVERY
The Rx Clock & Data Recovery is used to recover the clock signal
from the received data. It is accomplished by an integrated Digital Phase
Locked Loop (DPLL). The recovered clock tracks the jitter in the data
output from the Slicer and keeps the phase relationship between data
and clock during the absence of the incoming pulse.
Note that the IDT82P2521 also provides programmable REFA and
REFB pins to output any of the 22 recovered line clocks. Refer to
Section 3.5 Clock Inputs and Outputs for details.
3.1.5
DECODER
The Decoder is used only when the receive system interface is in
Single Rail NRZ Format mode. When the receive system interface is in
other modes, the Decoder is bypassed automatically. (Refer to
Section 3.1.6 Receive System Interface for the description of the receive
system interface).
The received signal is decoded by AMI or HDB3 line code rule. The
line code rule is selected by the R_CODE bit (b2, RCF1,...).
3.1.6
RECEIVE SYSTEM INTERFACE
The received data can be output to the system side in four modes:
Single Rail NRZ Format mode, Dual Rail NRZ Format mode, Dual Rail
RZ Format mode and Dual Rail Sliced mode, as selected by the
R_MD[1:0] bits (b1~0, RCF1).
If data is output on RDn in NRZ format and the recovered clock is
output on RCLKn, the receive system interface is in Single Rail NRZ
Format mode. In this mode, the data is decoded and updated on the
active edge of RCLKn. RCLKn outputs a 2.048 MHz clock. The Receive
Multiplex Function (RMFn) signal is updated on the active edge of
RCLKn and can be selected to indicate PRBS/ARB, LAIS, LEXZ, LBPV,
LEXZ + LBPV, LLOS, output recovered clock (RCLK) or XOR output of
positive and negative sliced data. Refer to Section 3.4.7.1 RMFn Indica-
tion for the description of RMFn.
If data is output on RDPn and RDNn in NRZ format and the recov-
ered clock is output on RCLKn, the receive system interface is in Dual
Rail NRZ Format mode. In this mode, the data is un-decoded and
updated on the active edge of RCLKn. RCLKn outputs a 2.048 MHz
clock.
If data is output on RDPn and RDNn in RZ format and the recovered
clock is output on RCLKn, the receive system interface is in Dual Rail
RZ Format mode. In this mode, the data is un-decoded and updated on
the active edge of RCLKn. RCLKn outputs a 2.048 MHz clock.
If data is output on RDPn and RDNn in RZ format directly after
passing through the Slicer, the receive system interface is in Dual Rail
Sliced mode. In this mode, the data is raw sliced and un-decoded.
RMFn can be selected to indicate PRBS/ARB, LAIS, LEXZ, LBPV, LEXZ
+ LBPV, LLOS, output recovered clock (RCLK) or XOR output of positive
and negative sliced data. Refer to Chapter 3.4.7.1 RMFn Indication for
the description of RMFn.
Table-2 summarizes the multiplex pin used in different receive
system interface.
Table-2 Multiplex Pin Used in Receive System Interface
Receive System
Interface
Multiplex Pin Used On Receive System
Interface
RDn / RDPn
RDNn / RMFn
RCLKn /
RMFn
Single Rail NRZ Format
RDn 1
RMFn 2
RCLKn 3
Dual Rail NRZ Format
RDPn 1
RDNn 1
RCLKn 3
Dual Rail RZ Format
RDPn 1
RDNn 1
RCLKn 3
Dual Rail Sliced
RDPn 1
RDNn 1
RMFn 2
Note:
1. The active level on RDn, RDPn and RDNn is selected by the RD_INV bit (b3,
RCF1,...).
2. RMFn is always active high.
3. The active edge of RCLKn is selected by the RCK_ES bit (b4, RCF1,...).
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72V3652L15PQF | IC BI FIFO 4096X36 15NS 132QFP |
| V48B12M250B3 | CONVERTER MOD DC/DC 12V 250W |
| V48B12M250B2 | CONVERTER MOD DC/DC 12V 250W |
| IDT72V3652L15PF | IC BI FIFO 4096X36 15NS 120QFP |
| IDT82V2088DR | IC LIU T1/J1/E1 8CH 208-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82P2521BHBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:21(1) Channel High-Density E1 Line Interface Unit |
| IDT82P2521BHG | 功能描述:IC LIU E1 21+1CH SHORT 640-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82P2521BHGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:21(1) Channel High-Density E1 Line Interface Unit |
| IDT82P2808 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:8(+1) Channel High-Density T1/E1/J1 Line Interface Unit |
| IDT82P2808BB | 功能描述:IC LIU T1/J1/E1 8+1CH 416-PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。