- 您現在的位置：買賣IC網 > PDF目錄8821 > IDT5T9890NLGI (IDT, Integrated Device Technology Inc)IC CLK DRIVER 2.5V PLL 68-VFQFPN PDF資料下載
參數資料
| 型號： | IDT5T9890NLGI |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 37/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK DRIVER 2.5V PLL 68-VFQFPN |
| 產品變化通告： | Product Discontinuation 05/Jan/2011 |
| 標準包裝： | 168 |
| 類型： | PLL 時鐘驅動器 |
| PLL： | 帶旁路 |
| 輸入： | eHSTL，HSTL，LVPECL，LVTTL |
| 輸出： | eHSTL，HSTL，LVTTL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:10 |
| 差分 - 輸入:輸出： | 是/無 |
| 頻率 - 最大： | 250MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 2.3 V ~ 2.7 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 68-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 68-VFQFPN（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 5T9890NLGI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁
9
INDUSTRIALTEMPERATURERANGE
IDT5T9890
EEPROM PROGRAMMABLE 2.5V PROGRAMMABLE SKEW PLL CLOCK DRIVER
EXTERNALDIFFERENTIALFEEDBACK
By providing a dedicated external differential feedback, the IDT5T9890
gives users flexibility with regard to divide selection. The FB and FB/
VREF2 signals are compared with the input REF[1:0] and REF[1:0]/VREF[1:0]
signals at the phase detector in order to drive the VCO. Phase differ-
ences cause the VCO of the PLL to adjust upwards or downwards
accordingly.
An internal loop filter moderates the response of the VCO to the
phase detector. The loop filter transfer function has been chosen to
provide minimal jitter (or frequency variation) while still providing accu-
rate responses to input frequency changes.
Output skew with respect to the REF[1:0] and REF[1:0]/VREF[1:0] input is adjustable to compensate for PCB trace delays, backplane propagation
delays or to accommodate requirements for special timing relationships between clocked components. Skew is selectable as a multiple of a time unit
(tU) which ranges from 250ps to 1.25ns (see Programmable Skew Range and Resolution Table). There are 18 skew/divide configurations
available for each output pair. These configurations are chosen through JTAG/I2C programming.
PROGRAMMABLESKEW
Bit 60 = 0
Bit 60 = 1
Comments
TimingUnitCalculation(tU)
1/(16 x FNOM)
VCO Frequency Range (FNOM)(1,2)
50 to 125MHz
100 to 250MHz
SkewAdjustmentRange(3)
Max Adjustment:
±8.75ns
±4.375ns
ns
±157.5°
PhaseDegrees
±43.75%
% of Cycle Time
Example 1, FNOM = 50MHz
tU = 1.25ns
—
Example 2, FNOM = 75MHz
tU = 0.833ns
—
Example 3, FNOM = 100MHz
tU = 0.625ns
Example 4, FNOM = 150MHz
—
tU = 0.417ns
Example 5, FNOM = 200MHz
—
tU = 0.313ns
Example 6, FNOM = 250MHz
—
tU = 0.25ns
PROGRAMMABLE SKEW RANGE AND RESOLUTION TABLE
NOTES:
1. The device may be operated outside recommended frequency ranges without damage, but functional operation is not guaranteed.
2. The VCO frequency always appears at nQ[1:0] outputs when they are operated in their undivided modes. The frequency appearing at the REF[1:0] and REF[1:0]/VREF[1:0] and
FB and FB/VREF2 inputs will be FNOM when the QFB and QFB are undivided and FB divide-by-1. The frequency of the REF[1:0] and REF[1:0]/VREF[1:0] and FB and FB/VREF2
inputs will be FNOM /2 or FNOM /4 when the part is configured for frequency multiplication by using a divided QFB and QFB and setting FB divide-by-1. Using the FB divide-
by-N configuration inputs allows a different method for frequency multiplication (see JTAG/I2C Serial Configurations: FB Divide-by-N).
3. Skew adjustment range assumes that a zero skew output is used for feedback. If a skewed QFB and QFB output is used for feedback, then adjustment range will be greater.
For example if a 4tU skewed output is used for feedback, all other outputs will be skewed –4tU in addition to whatever skew value is programmed for those outputs. ‘Max adjustment’
range applies to all output pairs where ±7tU skew adjustment is possible and at the lowest FNOM value.
INPUT/OUTPUT SELECTION(1)
Input
Output(2)
2.5V LVTTL SE
2.5VLVTTL,
1.8V LVTTL SE
1.8VLVTTL,
2.5V LVTTL DSE
HSTL,
1.8V LVTTL DSE
eHSTL
LVEPECL DSE
eHSTL DSE
HSTL DSE
2.5V LVTTL DIF
1.8V LVTTL DIF
LVEPECL DIF
eHSTL DIF
HSTL DIF
NOTES:
1. The INPUT/OUTPUT SELECTION Table describes the total possible combinations
of input and output interfaces. Single-Ended (SE) inputs in a single-ended mode require
the REF[1:0] /VREF[1:0] and FB/VREF2 pins to be left floating. Differential Single-Ended
(DSE) is for single-ended operation in differential mode, requiring VREF[1:0] and VREF2.
Differential (DIF) inputs are used only in differential mode.
2. For each output bank.
MASTER RESET FUNCTIONALITY
The IDT5T9890 performs a reset of the internal output divide circuitry
when all five output banks are disabled by toggling the nSOE pins
HIGH. When one or more banks of outputs are enabled by toggling the
nSOE LOW (if the corresponding nSOE programming bits are also set
LOW), the divide circuitry starts again from a known state. In the case
that the FB output is selected for divide-by-2 or divide-by-4, the FB
output will stop toggling while all five nSOE pins and bits are LOW, and
loss of lock will occur.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT5T9821NLI | IC CLK DRIVER ZD PLL 68-VFQFPN |
| VE-2W3-IV-S | CONVERTER MOD DC/DC 24V 150W |
| SY10ELT22LZI TR | IC TRANSLATOR DUAL 3.3V 8-SOIC |
| IDT5T9821NLGI8 | IC CLK DRIVER ZD PLL 68-VFQFPN |
| IDT5T9821NLGI | IC CLK DRIVER ZD PLL 68-VFQFPN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT5T9890NLGI8 | 功能描述:IC CLK DRIVER 2.5V PLL 68-VFQFPN RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| IDT5T9890NLI | 功能描述:IC CLK DRIVER 2.5V PLL 68-VFQFPN RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| IDT5T9890NLI8 | 功能描述:IC CLK DRIVER 2.5V PLL 68-VFQFPN RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| IDT5T9891NLGI | 功能描述:IC CLK DRIVER 2.5V PLL 68-VFQFPN RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| IDT5T9891NLGI8 | 功能描述:IC CLK DRIVER 2.5V PLL 68-VFQFPN RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。