- 您現在的位置：買賣IC網 > PDF目錄360790 > ICXO58CL AREA CCD IMAGE ARRAY PDF資料下載
參數資料
| 型號： | ICXO58CL |
| 英文描述： | AREA CCD IMAGE ARRAY |
| 中文描述： | 面陣CCD的圖像陣列 |
| 文件頁數： | 10/18頁 |
| 文件大小： | 203K |
| 代理商： | ICXO58CL |
– 10 –
ICX058CL
Image Sensor Characteristics Measurement Method
Measurement conditions
1) In the following measurements, the substrate voltage and the reset gate clock voltage are set to the values
indicated on the device, and the device drive conditions are at the typical values of the bias and clock
voltage conditions.
2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical
black (OB) level is used as the reference for the signal output, and the value measured at point [
A] in the
drive circuit example is used.
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance 706cd/m
2
, color temperature of 3200K halogen source) as a subject.
(Pattern for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR
cut filter and image at F8. The luminous intensity to the sensor receiving surface at this point is defined as
the standard sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the signal output (Vs) at the center of the screen and substitute the value into the
following formula.
S = Vs
×
[mV]
2. Saturation signal
Set to standard imaging condition
II
. After adjusting the luminous intensity to 10 times the intensity with
average value of the signal output, 200mV, measure the minimum value of the signal output.
3. Smear
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with average value of the signal output, 200mV. When the readout clock is stopped
and the charge drain is executed by the electronic shutter at the respective H blankings, measure the
maximum value VSm [mV] of the signal output and substitute the value into the following formula.
4. Video signal shading
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity so
that the average value of the signal output is 200mV. Then measure the maximum (Vmax [mV]) and
minimum (Vmin [mV]) values of the signal output and substitute the values into the following formula.
SH = (Vmax – Vmin)/200
×
100 [%]
5. Dark signal
Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature 60°C and
the device in the light-obstructed state, using the horizontal idle transfer level as a reference.
60
250
Sm =
×
100 [%] (1/10V method conversion value)
×
×
200
VSm
500
1
1
10
相關PDF資料 |
PDF描述 |
|---|---|
| ID1014 | White Bronze |
| ID1015 | Cable Stripping Process for SSMT Surface Mount Connector Series |
| ID101 | SCRs .5 Amp, Planar |
| ID101 | MONOLITHIC DUAL PICO AMPERE DIODES |
| ID1018 | Intermodulation in RF Coaxial Connectors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICY7C1357B-100BGI | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:9-Mb (256K x 36/512K x 18) Flow-Through SRAM with NoBL Architecture |
| ICY7C1357C-100BGI | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:9-Mbit (256K x 36/512K x 18) Flow-Through SRAM with NoBL Architecture |
| ICY7C1362B-166BGI | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:9-Mbit (256K x 36/512K x 18) Pipelined SRAM |
| ICY7C1362C-166BGI | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:9-Mbit (256K x 36/512K x 18) Pipelined SRAM |
| ICY7C1362C-166BGXI | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:9-Mbit (256K x 36/512K x 18) Pipelined SRAM |
發布緊急采購，3分鐘左右您將得到回復。