- 您現在的位置：買賣IC網 > PDF目錄360785 > ICS950104 Programmable System Clock Chip for PIII Processor PDF資料下載
參數資料
| 型號： | ICS950104 |
| 英文描述： | Programmable System Clock Chip for PIII Processor |
| 中文描述： | 可編程系統時鐘芯片的PIII處理器 |
| 文件頁數： | 15/19頁 |
| 文件大?。?/td> | 222K |
| 代理商： | ICS950104 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁
15
ICS950104
Advance Information
Third party brands and names are the property of their respective owners.
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In
this mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for these
pins, a resistor is connected to either the VDD (logic 1) power
supply or the GND (logic 0) voltage potential. A 10 Kilohm
(10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
8.2K
Figure 1 shows a means of implementing this function when
a switch or 2 pin header is used. With no jumper is installed
the pin will be pulled high. With the jumper in place the pin
will be pulled low. If programmability is not necessary, than
only a single resistor is necessary. The programming resistors
should be located close to the series termination resistor to
minimize the current loop area. It is more important to locate
the series termination resistor close to the driver than the
programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS950202 | Programmable Timing Control HubTM for P4TM |
| ICS950208 | Programmable Timing Control Hub for P4 |
| ICS950211 | Programmable Timing Control Hub for P4 |
| ICS950211YFLF-T | Programmable Timing Control Hub for P4 |
| ICS950211YGLF-T | Programmable Timing Control Hub for P4 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS950104YFT | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable System Clock Chip for PIII Processor |
| ICS950201 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub⑩ for P4⑩ |
| ICS950201AFLF | 功能描述:IC TIMING CTRL HUB P4 56-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:TCH™ 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6 |
| ICS950201AFLFT | 功能描述:IC TIMING CTRL HUB P4 56-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:TCH™ 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ICS950201AFT-IB0 | 制造商:Ics 功能描述:ELECTRONIC COMPONENT 制造商:Integrated Device Technology Inc 功能描述:ELECTRONIC COMPONENT |
發布緊急采購，3分鐘左右您將得到回復。