- 您現在的位置：買賣IC網 > PDF目錄360767 > ICS8430-51 600MHZ, LOW JITTER LVCMOS/ LVTTL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER PDF資料下載
參數資料
| 型號： | ICS8430-51 |
| 英文描述： | 600MHZ, LOW JITTER LVCMOS/ LVTTL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER |
| 中文描述： | 600MHz的，低抖動的LVCMOS / LVTTL至3.3伏的LVPECL頻率合成器 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 147K |
| 代理商： | ICS8430-51 |
8430AY-51
www.icst.com/products/hiperclocks.html
REV. D FEBRUARY 11, 2003
2
PRELIMINARY
ICS8430-51
600MH
Z
, L
OW
J
ITTER
LVCMOS/LVTTL-
TO
-3.3V LVPECL F
REQUENCY
S
YNTHESIZER
NOTE: The functional description that follows describes operation using a 16MHz crystal. Valid PLL loop divider values for
different crystal or input frequencies are defined in the Input Frequency Characteristics, Table 5, NOTE 1.
The ICS8430-51 features a fully integrated PLL and therefore requires no external components for setting the loop band-
width. A parallel-resonant, fundamental crystal is used as the input to the on-chip oscillator. The output of the oscillator is
divided by 16 prior to the phase detector. With a 16MHz crystal, this provides a 1MHz reference frequency. The VCO of the
PLL operates over a range of 200MHz to 700MHz. The output of the M divider is also applied to the phase detector.
The phase detector and the M divider force the VCO output frequency to be 2M times the reference frequency by adjusting the
VCO control voltage. Note that for some values of M (either too high or too low), the PLL will not achieve lock. The output of the
VCO is scaled by a divider prior to being sent to each of the LVPECL output buffers. The divider provides a 50% output duty cycle.
The programmable features of the ICS8430-51 support two input modes, programmable M divider and N output divider.
The two input operational modes are parallel and serial. Figure 1shows the timing diagram for each mode. In parallel mode,
the nP_LOAD input is initially LOW. The data on inputs M0 through M8 and N0 through N2 is passed directly to the M divider
and N output divider. On the LOW-to-HIGH transition of the nP_LOAD input, the data is latched and the M divider remains
loaded until the next LOW transition on nP_LOAD or until a serial event occurs. As a result, the M and N bits can be
hardwired to set the M divider and N output divider to a specific default state that will automatically occur during power-up.
The TEST output is LOW when operating in the parallel input mode. The relationship between the VCO frequency, the crystal
frequency and the M divider is defined as follows:
The M value and the required values of M0 through M8 are shown in Table 3B, Programmable VCO Frequency Function Table.
Valid M values for which the PLL will achieve lock for a 16MHz reference are defined as 100
≤
M
≤
350. The frequency out is
defined as follows:
N
Serial operation occurs when nP_LOAD is HIGH and S_LOAD is LOW. The shift register is loaded by sampling the S_DATA
bits with the rising edge of S_CLOCK. The contents of the shift register are loaded into the M divider and N output divider
when S_LOAD transitions from LOW-to-HIGH. The M divide and N output divide values are latched on the HIGH-to-LOW
transition of S_LOAD. If S_LOAD is held HIGH, data at the S_DATA input is passed directly to the M divider and N output
divider on each rising edge of S_CLOCK. The serial mode can be used to program the M and N bits and test bits T1 and T0.
The internal registers T0 and T1 determine the state of the TEST output as follows:
F
UNCTIONAL
D
ESCRIPTION
T1
T0
TEST Output
0
0
LOW
0
1
S_Data
1
0
Output of M divider
1
1
CMOS Fout
F
IGURE
1. P
ARALLEL
& S
ERIAL
L
OAD
O
PERATIONS
Time
S
ERIAL
L
OADING
P
ARALLEL
L
OADING
M, N
t
S
t
H
t
S
t
H
t
S
T1
T0
N2
N1
N0
M8
M7
M6
M5
M4
M3
M2
M1
M0
*NOTE: The NULL timing slot must be observed.
S_CLOCK
S_DATA
S_LOAD
nP_LOAD
M0:M8, N0:N2
nP_LOAD
fout =fVCO=fxtalxN
2M
fVCO =16
相關PDF資料 |
PDF描述 |
|---|---|
| ICS8430AY-51 | 600MHZ, LOW JITTER LVCMOS/ LVTTL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER |
| ICS8430AY-51T | 600MHZ, LOW JITTER LVCMOS/ LVTTL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER |
| ICS8430-61 | 500MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER |
| ICS8430AYI-61 | 500MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER |
| ICS8430AYI-61T | 500MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS843051AG | 制造商:ICS 制造商全稱:ICS 功能描述:FEMTOCLOCKS CRYSTAL-TO-3.3V LVPECL CLOCK GENERATOR |
| ICS843051AGLF | 功能描述:IC CLK GEN GIG ETH LVPECL 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™, FemtoClock™ 標準包裝:2,000 系列:- 類型:PLL 頻率合成器 PLL:是 輸入:晶體 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大:1GHz 除法器/乘法器:是/無 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-LSSOP（0.175"，4.40mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:NJW1504V-TE1-NDNJW1504V-TE1TR |
| ICS843051AGLFT | 功能描述:IC CLOCK GENERATOR LVPECL 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™, FemtoClock™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS843051AGT | 制造商:ICS 制造商全稱:ICS 功能描述:FEMTOCLOCKS CRYSTAL-TO-3.3V LVPECL CLOCK GENERATOR |
| ICS8430-61 | 制造商:ICS 制造商全稱:ICS 功能描述:500MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER |
發布緊急采購，3分鐘左右您將得到回復。