- 您現在的位置：買賣IC網 > PDF目錄360767 > ICS8430-51 600MHZ, LOW JITTER LVCMOS/ LVTTL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER PDF資料下載
參數資料
| 型號： | ICS8430-51 |
| 英文描述： | 600MHZ, LOW JITTER LVCMOS/ LVTTL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER |
| 中文描述： | 600MHz的，低抖動的LVCMOS / LVTTL至3.3伏的LVPECL頻率合成器 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 147K |
| 代理商： | ICS8430-51 |
8430AY-51
www.icst.com/products/hiperclocks.html
REV. D FEBRUARY 11, 2003
11
PRELIMINARY
ICS8430-51
600MH
Z
, L
OW
J
ITTER
LVCMOS/ LVTTL-
TO
-3.3V LVPECL F
REQUENCY
S
YNTHESIZER
The following component footprints are used in this layout
example: All the resistors and capacitors are size 0603.
P
OWER
AND
G
ROUNDING
Place the decoupling capacitors C14 and C15 as close as pos-
sible to the power pins. If space allows, placing the decoupling
capacitor at the component side is preferred. This can reduce
unwanted inductance between the decoupling capacitor and the
power pin generated by the via.
Maximize the pad size of the power (ground) at the decoupling
capacitor. Maximize the number of vias between power (ground)
and the pads. This can reduce the inductance between the power
(ground) plane and the component power (ground) pins.
If V
shares the same power supply with V
, insert the RC
filter R7, C11, and C16 in between. Place this RC filter as close
to the V
CCA
as possible.
C
LOCK
T
RACES
AND
T
ERMINATION
The component placements, locations and orientations should be
arranged to achieve the best clock signal quality. Poor clock signal
quality can degrade the system performance or cause system fail-
ure. In the synchronous high-speed digital system, the clock signal
is less tolerable to poor signal quality than other signals. Any ring-
ing on the rising or falling edge or excessive ring back can cause
system failure. The trace shape and the trace delay might be re-
stricted by the available space on the board and the component
location. While routing the traces, the clock signal traces should be
routed first and should be locked prior to routing other signal traces.
The traces with 50
transmission lines TL1 and TL2 at
FOUT and nFOUT should have equal delay and run ad-
jacent to each other. Avoid sharp angles on the clock trace.
Sharp angle turns cause the characteristic impedance to
change on the transmission lines.
Keep the clock trace on the same layer. Whenever pos-
sible, avoid any vias on the clock traces. Any via on the
trace can affect the trace characteristic impedance and
hence degrade signal quality.
To prevent cross talk, avoid routing other signal traces in
parallel with the clock traces. If running parallel traces is
unavoidable, allow more space between the clock trace
and the other signal trace.
Make sure no other signal trace is routed between the
clock trace pair.
The matching termination resistors R1, R2, R3 and R4 should
be located as close to the receiver input pins as possible. Other
termination schemes can also be used but are not shown in
this example.
C
RYSTAL
The crystal X1 should be located as close as possible to the pins
24 (XTAL1) and 25 (XTAL2). The trace length between the X1
and U1 should be kept to a minimum to avoid unwanted parasitic
inductance and capacitance. Other signal traces should not be
routed near the crystal traces.
F
IGURE
6B. PCB B
OARD
L
AYOUT
FOR
ICS8430-51
TL1, TL2 are 50 Ohm traces and
C15
C16
VCC
T
R4
VIA
R7
R1
GND
U1
TL1
R3
X1
Close to the input
pins of the
receiver
C14
PIN 1
T
VCCA
TL1N
R2
C11
相關PDF資料 |
PDF描述 |
|---|---|
| ICS8430AY-51 | 600MHZ, LOW JITTER LVCMOS/ LVTTL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER |
| ICS8430AY-51T | 600MHZ, LOW JITTER LVCMOS/ LVTTL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER |
| ICS8430-61 | 500MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER |
| ICS8430AYI-61 | 500MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER |
| ICS8430AYI-61T | 500MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS843051AG | 制造商:ICS 制造商全稱:ICS 功能描述:FEMTOCLOCKS CRYSTAL-TO-3.3V LVPECL CLOCK GENERATOR |
| ICS843051AGLF | 功能描述:IC CLK GEN GIG ETH LVPECL 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™, FemtoClock™ 標準包裝:2,000 系列:- 類型:PLL 頻率合成器 PLL:是 輸入:晶體 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大:1GHz 除法器/乘法器:是/無 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-LSSOP（0.175"，4.40mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:NJW1504V-TE1-NDNJW1504V-TE1TR |
| ICS843051AGLFT | 功能描述:IC CLOCK GENERATOR LVPECL 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™, FemtoClock™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS843051AGT | 制造商:ICS 制造商全稱:ICS 功能描述:FEMTOCLOCKS CRYSTAL-TO-3.3V LVPECL CLOCK GENERATOR |
| ICS8430-61 | 制造商:ICS 制造商全稱:ICS 功能描述:500MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER |
發布緊急采購，3分鐘左右您將得到回復。