- 您現在的位置：買賣IC網 > PDF目錄384476 > ICB1FL02G (INFINEON TECHNOLOGIES AG) Smart Ballast Control IC for Fluorescent Lamp Ballasts PDF資料下載
參數資料
| 型號： | ICB1FL02G |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | Smart Ballast Control IC for Fluorescent Lamp Ballasts |
| 中文描述： | 智能鎮流器控制芯片用于熒光燈鎮流器 |
| 文件頁數： | 6/37頁 |
| 文件大?。?/td> | 1143K |
| 代理商： | ICB1FL02G |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
ICB1FL02G
Pin Configuration and Description
Datasheet Version 1.2
6
February 2006
PFCGD (PFC gate drive, Pin 5)
The Gate of the MOSFET in the PFC preconverter
designed in boost topology is controlled by this pin.
There is an active L-level during UVLO and a limitation
of the max. H-level at 11V during normal operation.
Turning on the MOSFET softly (with a reduced di
/
dt), the Gate drive voltage rises within 220ns from L-
level to H-level. The fall time of the Gate voltage is less
than 50ns in order to turn off quickly. A resistor of about
10Ohm between drive pin and Gate in order to avoid
oscillations and in order to shift the power dissipation of
discharging the Gate capacitance into this resistor is
recommended.
The PFC section of the IC controls a boost converter as
a PFC preconverter in discontinuous conduction mode
(DCM). Typically the control starts with Gate drive
pulses with an on-time of 1
μ
s increasing up to 24
μ
s and
a off-time of 40
μ
s. As soon as a sufficient ZCD (zero
current detector) signal is available, the operating
mode changes from a fixed frequent operation to an
operation with variable frequency. During rated and
medium load conditions we get an operation with
critical conduction mode (CritCM), that means
triangular shaped currents in the boost converter choke
without gaps when reaching the zero level and variable
operating frequency. During light load (detected by the
internal error amplifier) we get an operation with
discontinuous conduction mode (DCM), that means
triangular shaped currents in the boost converter choke
with gaps when reaching the zero level and variable
operating frequency in order to avoid steps in the
consumed line current.
PFCCS (PFC current sense, Pin 6)
The voltage drop across a shunt resistor located
between Source of the PFC MOSFET and GND is
sensed with this pin. If the level exceeds a threshold of
1V for longer than 260ns the PFC Gate drive is turned
off as long as the ZCD (zero current detector) enables
a new cycle. If there is no ZCD signal available within
40μs after turn-off of the PFC Gate drive, a new cycle
is initiated from an internal start-up timer.
PFCZCD (PFC zero current detection, Pin 7)
This pin senses the point of time when the current
through the boost inductor becomes zero during off-
time of the PFC MOSFET in order to initiate a new
cycle. The moment of interest appears when the
voltage of the separate ZCD winding changes from
positive to negative level which represents a voltage of
zero at the inductor windings and therefore the end of
current flow from lower input voltage level to higher
output voltage level. There is a threshold with
hysteresis, for increasing voltage a level of 1,5V, for
decreasing voltage a level of 0,5V, that detects the
change of inductor voltage. A resistor connected
between ZCD winding and sense input limits the sink
and source current of the sense pin, when the voltage
of the ZCD winding exceeds the internal clamping
levels (6,3V and -2,9V @ 4mA) of the IC.
If the sensed level of the ZCD winding is not sufficient
(e.g. during start-up), an internal start-up timer will
initiate a new cycle every 40
μ
s after turn-off of the PFC
Gate drive.
PFCVS (PFC voltage sense, Pin 8)
The intermediate circuit voltage (bus voltage) at the
smoothing capacitor is sensed by a resistive divider at
this pin. The internal reference voltage for rated bus
voltage is 2,5V. There are further thresholds at 0,375V
(15% of rated bus voltage), 1,83V (73% of rated bus
voltage) and 2,725V (109% of rated bus voltage) for
detecting open control loop, undervoltage and
overvoltage.
RFRUN (Set R for run frequency, Pin 9)
A resistor from this pin to ground sets the operating
frequency of the inverter during run mode. Typical run
frequency range is 20kHz to 100kHz. The set resistor
R
RFRUN
can be calculated based on the run frequency
f
RUN
according to the equation
Hz
fRUN
RFPH (Set R for preheating frequency, Pin 10)
A resistor from this pin to ground sets together with the
resistor at pin 9 the operating frequency of the inverter
during preheat mode. Typical preheat frequency range
is run frequency (as a minimum) to 150kHz. The set
resistor R
RFPH
can be calculated based on the preheat
frequency f
PH
and the resistor R
RFRUN
according to the
equation:
5 108
Hz
The total value of both resistors R
RFPH
and R
RFRUN
switched in parallel should not be less than 3,3kOhm.
RTPH (Set R for preheating time, Pin 11)
A resistor from this pin to ground sets the preheating
time of the inverter during preheat mode. A set resistor
range from zero to 18kOhm corresponds to a range of
preheating time from zero to 2000ms subdivided in 127
steps.
RES (Restart after lamp removal, Pin 12)
A source current out of this pin via resistor and filament
to ground monitors the existence of the low-side
filament of the fluorescent lamp for restart after lamp
RRFRUN
5 108
=
RRFPH
RRFRUN
fPH
1
–
------------RRFRUN
=
相關PDF資料 |
PDF描述 |
|---|---|
| ICE1QS01 | Controller for Switch Mode Power Supplies Supporting Low Power Standby and Power Factor Correction (PFC) |
| ICE1QS01G | Controller for Switch Mode Power Supplies Supporting Low Power Standby and Power Factor Correction (PFC) |
| ICE3AS02 | Off-Line SMPS Current Mode Controller with integrated 500V Startup Cell |
| ICE3AS02G | Off-Line SMPS Current Mode Controller with integrated 500V Startup Cell |
| ICE3BS02 | Off-Line SMPS Current Mode Controller with integrated 500V Startup Cell |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICB1FL02G IFX | 制造商:Infineon Technologies AG 功能描述: |
| ICB1FL02G_08 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Smart Ballast Control IC for Fluorescent Lamp Ballasts |
| ICB1FL02GXUMA1 | 制造商:Infineon Technologies AG 功能描述:Electronic Ballast Controller 12V/15V 100KHz T/R 制造商:Infineon Technologies AG 功能描述:Electronic Ballast Controller 12V/15V 100KHz 18-Pin DSO T/R 制造商:Infineon Technologies AG 功能描述:FL LIGHTING - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC SMART BALLAST CONTROL PDSO-18 |
| ICB1FL03G | 功能描述:LED照明驅動器 LIGHTING RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| ICB1FL03GXUMA1 | 制造商:Infineon Technologies AG 功能描述:ELECTRONIC BALLAST CONTROLLER 12V/15V 100KHZ 制造商:Infineon Technologies AG 功能描述:FL LIGHTING - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC SMART BALLAST CONTROL DSO18 |
發布緊急采購，3分鐘左右您將得到回復。