參數資料
型號： I5116X
廠商： WINBOND ELECTRONICS CORP
元件分類： 音頻合成
英文描述： SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
中文描述： 960 SEC, SPEECH SYNTHESIZER WITH RCDG, UUC25
封裝： DIE-25
文件頁數： 36/88頁
文件大?。?/td> 612K
代理商： I5116X
ISD5100 – SERIES
- 36 -
7.5. D
IGITAL
M
ODE
7.5.1. Erasing Digital Data
The Digital Erase command can only erase an entire page at a time. This means that the D1
command only needs to include the 11-bit page address; the 5-bit for block address are left at 00000.
Once a page has been erased, each block may be written separately, 64 bits at a time. But, if a block
has been previously written then the entire page of 2048 bits must be erased in order to re-write (or
change) a block.
A sequence might be look like:
- read the entire page
- store it in RAM
- change the desired bit(s)
- erase the page
- write the new data from RAM to the entire page
7.5.2. Writing Digital Data
The Digital Write function allows the user to select a portion of the array to be used as digital memory.
The partition between analog and digital memory is left up to the user. A page can only be either
Digital or Analog, but not both. The minimum addressable block of memory in the digital mode is one
block or 64 bits, when reading or writing. The address sent to the device is the 11-bit row (or page)
address with the 5-bit scan (or block) address. However, one must send a Digital Erase before
attempting to change digital data on a page. This means that even when changing only one of the 32
blocks, all 32 blocks will need to be rewritten to the page. Command Sequence: The chip enters
digital mode by sending the ENTER DIGITAL MODE command from power down. Send the
DIGITAL WRITE @ ADDR command with the row address. After the address is entered, the data is
sent in one-byte packets followed by an I
C acknowledge generated by the chip. Data for each block
is sent MSB first. The data transfer is ended when the master generates an I
2
C STOP condition. If
only a partial block of data is sent before the STOP condition, “zero” is written in the remaining bytes;
that is, they are left at the erase level. An erased page (row) will be read as all zeros. The device can
buffer up to two blocks of data. If the device is unable to accept more data due to the internal write
process, the SCL line will be held LOW indicating to the master to halt data transfer.
If the device
encounters an overflow condition, it will respond by generating an interrupt condition and an I
2
C Not
Acknowledge signal after the last valid byte of data. Once data transfer is terminated, the device
needs up to two cycles (64 us) to complete its internal write cycle before another command is sent. If
an active command is sent before the internal cycle is finished, the part will hold SCL LOW until the
current command is finished. After writing is complete, send the EXIT DIGITAL MODE command.
相關PDF資料
PDF描述
I5102EI SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
I5102S SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
I5102SI SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
I5102X SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
I5104E SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
相關代理商/技術參數
參數描述
I511E12 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:OMNUC M-Series User Manual DX CODE ZA
I511ERW 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Ultra-Miniature 5W Single & Dual Output DC/DC Converters
I511RU 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:4:1 Input, 5W Ultra-Miniature DC/DC Converters
I512E12 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:OMNUC U-Series(1 to 5kW) DX CODE ZA
I512ERW 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Ultra-Miniature 5W Single & Dual Output DC/DC Converters
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*