- 您現在的位置：買賣IC網 > PDF目錄385404 > HT82V24 (Holtek Semiconductor Inc.) 16-Bit, 15MSPS, 3-Channel CCD/CIS Analog Signal Processor PDF資料下載
參數資料
| 型號： | HT82V24 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 16-Bit, 15MSPS, 3-Channel CCD/CIS Analog Signal Processor |
| 中文描述： | 16位，15MSPS，3通道防治荒漠化公約/獨聯體模擬信號處理器 |
| 文件頁數： | 7/21頁 |
| 文件大小： | 216K |
| 代理商： | HT82V24 |
HT82V24
Rev. 1.00
7
September 7, 2005
-
6
7
8 8 !
9
8 8 !
)
'
%
0 :
&
-
6
7
;
9
;
/
/
)
'
%
0 :
2
Bit D0 control the ADC output cycle of the HT82V24.
Bit D8 selects the ADC data output format selection. Setting D8 high enables the WM mode data output format while
settingbitD8lowenablestheADImodeoutputdataformat.TheonenibbledatawilloutputdatatopinsD7~D4and4 4
(WM) mode output the data format selected. The output format as the following table:
D8
D0
ADC Output Format
0
0
D5=1: 3-CH 8 2 (ADI)
D5=0: 1 or 2-CH 8 2 (ADI)
0
1
D5=1: 3-CH 8 1 (ADI)
D5=0: 1 or 2-CH 8 1 (ADI)
1
0
D5=0: 1-CH 4 4 (WM)
1
1
D5=1: 3-CH 8 2 (WM)
D5=0: 1-CH 8 2 (WM)
-
6
7 % ;
9 % ;
-
6
7 % ;
)
'
%
0 :
2
)
'
%
0 :
2
/
6
7 % ;
MUX Register
The MUX register controls the sampling channel order
and the 2-channel mode configuration in the HT82V24.
Bit D8 is used to set the output latency in ADC clock pe-
riod and is only valid when WM mode data output format
is selected. Bit D7 is used when operating in the
3-channel mode or the 2-channel mode. Setting bit D7
high will sequence the MUX to sample the red channel
first, then the green channel, and then the blue channel.
When in the 3-channel mode, the CDSCLK2 rising edge
always resets the MUX to sample the red channel first
(see timing diagrams). When bit D7 is set low, the chan-
nel order is reversed to blue first, green second, and red
third. The CDSCLK2 rising edge will always reset the
MUX to sample the blue channel first. Bits D6, D5 and
D4 are used when operating in 1 or 2-channel mode. Bit
D6 is set high to sample the red channel. Bit D5 is set
high to sample the green channel. Bit D4 is set high to
sample the blue channel. The MUX will remain station-
ary during 1-channel mode. The two channel mode is
selected by setting two of the channel select bits
(D4~D6) high. The MUX samples the channels in the or-
der selected by bit D7. In WM mode, Bits D0~D2 are
used to control the sampling point delay option. Bit D3 is
used to select the rising or falling edge on the CDSCLK1
input pin and generates an internal VSMP pulse. Bits
D0~D3 set to 0 in ADI Mode.
D8
D7
D6
D5
D4
D3
D2
D1
D0
Set to 0
MUX Order
Channel Select
Set to 0
1=R-G-B*
1=RED*
1=GREEN
1=BLUE
0=B-G-R
0=Off
0=Off*
0=Off*
MUX Register Settings (ADI Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| HT82V26A | 16-Bit CCD/CIS Analog Signal Processor |
| HT82V26 | 16-Bit CCD/CIS Analog Signal Processor |
| HT82V36 | 16-Bit CCD/CIS Analog Signal Processor |
| HT82V731 | Audio D/A Converter |
| HT82V732 | Protective Eyeglasses |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82V26 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:16-Bit CCD/CIS Analog Signal Processor |
| HT82V26A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:16-Bit CCD/CIS Analog Signal Processor |
| HT82V36 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:16-Bit CCD/CIS Analog Signal Processor |
| HT82V38 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:16-Bit CCD/CIS Analog Signal Processor |
| HT82V42 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Single-channel 16-Bit CCD/CIS Analog Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。