參數資料
型號: HT82J97E-20SOP-A
廠商: Holtek Semiconductor Inc.
英文描述: USB Joystick Encoder 8-Bit OTP MCU
中文描述: USB搖桿編碼器8位微控制器檢察官辦公室
文件頁數: 19/46頁
文件大?。?/td> 314K
代理商: HT82J97E-20SOP-A
HT82J97E
Rev. 1.30
19
May 10, 2004
Therearesometimingconstrainsandusagesillustratedhere.BysettingtheMISCregister,theMCUcanperformread-
ing,writingandclearingactions.TherearesomeexamplesshowninthefollowingtableforendpointFIFOreading,writ-
ing and clearing.
Actions
MISC Setting Flow and Status
Read FIFO0 sequence
00H
and check if not ready (01H)
01H
delay of 2 s, check 41H
read* from FIFO0 register
02H
03H
Write FIFO1 sequence
0AH
check if not ready (0BH)
0BH
delay of 2 s, check 4BH
write* to FIFO1 register and
09H
08H
Check whether FIFO0 can be read or not
00H
ready)
01H
delay of 2 s, check 41H (if ready) or 01H (if not
00H
CheckwhetherFIFO1canbewrittentoornot
0AH
ready)
0BH
0AH
delay of 2 s, check 4BH (if ready) or 0BH (if not
Write 0-sized packet sequence to FIFO 0
02H
03H
delay of 2 s, check 43H
01H
00H
Note: *: There are 2 s gap existing between 2 reading actions or between 2 writing actions
Register Name
R/W
Register Address
Bit7~Bit0
FIFO 0
R/W
01001000B
Data7~Data0
FIFO 1
R/W
01001001B
Data7~Data0
FIFO Register Address Table
USB Active Pipe Timing
TheUSBactivepipeaccessedbythehostcannotbeusedbytheMCUsimultaneously.Whenthehostfinishesitswork,
the signal, a USB_INT will be produced to tell the MCU that the pipe can be used and the acted pipe No. will be shown
in the signal, ACT_PIPE as well. The timing is illustrated in the Figure below.
USB Active Pipe Timing
- B
B
#
! (
" (
Suspend Wake-Up and Remote Wake-Up
If there is no signal on the USB bus for over 3ms, the
HT82J97E will go into a suspend mode. The Suspend
line (bit 0 of the USC) will be set to 1 and a USB interrupt
is triggered to indicate that the HT82J97E should jump
to the suspend state to meet the 500 A USB suspend
current spec.
In order to meet the 500 A suspend current, the pro-
grammer should disable the USB clock by clearing the
USBCKEN (bit3 of the SCC) to 0 . The suspend cur-
rent is 400 A.
The user can also further decrease the suspend current
to 250 A by setting the SUSP2 (bit4 of the SCC). But if
the SUSP2 is set, the user has to make sure not to en-
able the LVR OPT option, otherwise the HT82J97E will
be reset.
When the resume signal is sent out by the host, the
HT82J97E will wake-up the MCU by USB interrupt and
the Resume line (bit 3 of the USC) is set. In order to
make the HT82J97E function properly, the programmer
must set the USBCKEN (bit 3 of the SCC) to 1 and clear
the SUSP2 (bit4 of the SCC). Since the Resume signal
will be cleared before the Idle signal is sent out by the
host and the Suspend line (bit 0 of the USC) is going to
0 . So when the MCU is detecting the Suspend line
(bit0 of the USC), the Resume line should be remem-
bered and taken into consideration.
After finishing the resume signal, the suspend line will
go inactive and a USB interrupt is triggered. The follow-
ing is the timing diagram:
- (
!
(
,
- B
相關PDF資料
PDF描述
HT82J97E-28SOP-A USB Joystick Encoder 8-Bit OTP MCU
HT82K28 Win98 Keyboard Encoder
HT82K28A Win98 Keyboard Encoder
HT82K628A Windows 2000 Keyboard Encoder(Windows 2000操作系統鍵盤編碼器)
HT82K628 Windows 2000 Keyboard Encoder
相關代理商/技術參數
參數描述
HT82J97E-28SOP-A 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Joystick Encoder 8-Bit OTP MCU
HT82K19 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC
HT82K28 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Win98 Keyboard Encoder
HT82K28A 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Win98 Keyboard Encoder
HT82K28A_02 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Win98 Keyboard Encoder