- 您現在的位置：買賣IC網 > PDF目錄385399 > HT46R46 (Holtek Semiconductor Inc.) Cost-Effective A/D Type 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT46R46 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | Cost-Effective A/D Type 8-Bit MCU |
| 中文描述： | 成本效益的A / D型8位微控制器 |
| 文件頁數： | 12/42頁 |
| 文件大?。?/td> | 291K |
| 代理商： | HT46R46 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
HT46R46/HT46C46/HT46R47/HT46C47
Rev. 1.00
12
December 28, 2004
Power Down Operation
HALT
The HALT mode is initialized by the HALT instruction
and results in the following...
The system oscillator will be turned off but the WDT
oscillator keeps running (if the WDT oscillator is se-
lected).
The contents of the on chip RAM and registers remain
unchanged.
WDT will be cleared and recounted again (if the WDT
clock is from the WDT oscillator).
All of the I/O ports maintain their original status.
The PDF flag is set and the TO flag is cleared.
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge sig-
nal on port A or a WDT overflow. An external reset
causes a device initialization and the WDToverflow per-
forms a warm reset . After the TO and PDF flags are
examined, the reason for chip reset can be determined.
The PDF flag is cleared by system power-up or execut-
ing the CLR WDT instruction and is set when execut-
ing the HALT instruction. The TO flag is set if the WDT
time-out occurs, and causes a wake-up that only resets
the program counter and SP; the others keep their origi-
nal status.
The port A wake-up and interrupt methods can be con-
sidered as a continuation of normal execution. Each bit
in port A can be independently selected to wake up the
device by the options. Awakening from an I/O port stim-
ulus, the program will resume execution of the next in-
struction. If it is awakening from an interrupt, two
sequences may happen. If the related interrupt is dis-
abled or the interrupt is enabled but the stack is full, the
program will resume execution at the next instruction. If
theinterruptisenabledandthestackisnotfull,theregu-
lar interrupt response takes place. If an interrupt request
flag is set to 1 before entering the HALT mode, the
wake-upfunctionoftherelatedinterruptwillbedisabled.
Once a wake-up event occurs, it takes 1024 t
SYS
(sys-
tem clock period) to resume normal operation. In other
words, a dummy period will be inserted after wake-up. If
the wake-up results from an interrupt acknowledgment,
the actual interrupt subroutine execution will be delayed
by one or more cycles. If the wake-up results in the next
instruction execution, this will be executed immediately
after the dummy period is finished.
To minimize power consumption, all the I/O pins should
be carefully managed before entering the HALT status.
Reset
There are three ways in which a reset can occur:
RES reset during normal operation
RES reset during HALT
WDT time-out reset during normal operation
The WDT time-out during HALT is different from other
chip reset conditions, since it can perform a warm re -
set that resets only the program counter and SP, leav-
ing the other circuits in their original state. Some regis-
ters remain unchanged during other reset conditions.
Most registers are reset to the initial condition when
the reset conditions are met. By examining the PDF and
TO flags, the program can distinguish between different
chip resets .
TO PDF
RESET Conditions
0
0
RES reset during power-up
u
u
RES reset during normal operation
0
1
RES wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT wake-up HALT
Note: u means unchanged
$ %
0 " =
7 2 > !
6 2 > !
'
+
!
0 "
+
+
!
2
)
4 )
5
)
Watchdog Timer
相關PDF資料 |
PDF描述 |
|---|---|
| HT46C62 | A/D with LCD Type 8-Bit MCU |
| HT46R62 | A/D with LCD Type 8-Bit MCU |
| HT46C63 | A/D with LCD Type 8-Bit MCU |
| HT46C63-100QEP-A | A/D with LCD Type 8-Bit MCU |
| HT46C63-56SSOP-A | A/D with LCD Type 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT46R46_08 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit MCU |
| HT46R46E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit MCU |
| HT46R46E_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit MCU |
| HT46R46-H | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit OTP MCU |
| HT46R47 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit OTP Battery Charger Controller |
發布緊急采購，3分鐘左右您將得到回復。