- 您現在的位置：買賣IC網 > PDF目錄384423 > HIP9011AB (INTERSIL CORP) Engine Knock Signal Processor PDF資料下載
參數資料
| 型號： | HIP9011AB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Engine Knock Signal Processor |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | PLASTIC, MS-013-AC, SOIC-20 |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 76K |
| 代理商： | HIP9011AB |
4-6
Description of the HIP9011 Operation
This IC is designed to be a universal digitally controlled, analog
interfacebetweenengineacousticalsensorsoraccelerometers
and internal combustion engine fuel management systems.
Two wideband input amplifiers are provided which will allow the
use of two sensors. These sensors be of the piezoelectric type,
that can be mounted in optimum locations on either in-line or V
type engine configurations.
Output from these input amplifiers are directed to a channel
select mux switch and then into a 3rd order antialiasing filter.
The output signal is then directed to two programmable gain
stages, where one stage inverts or shifts the knock signal 180
degrees. The gain stage signals are outputted to two
programmable bandpass filter stages. Outputs from the two
BPF stages are then full wave rectified before being digitally
integrated by the programmable integrator. The integrator
output is applied to a line driver for further processing by the
engine fuel management control system. The gain, bandpass
filter and integrator stage settings are programmable from a
microprocessor via the SPI Bus Interface
Broadband piezoelectric ceramic transducers used for the
engine signal pickup have device capacitances in the order
of 1100pF and output voltages that range from 5mV to 8V
RMS. During normal engine operation, a single input
channel is selected and applied to the HIP9011. The engine
background noise is typically well below in amplitude than
the pre-detonation noise. Therefore, the bandpass filter
stages can be optimized to further discriminate between
engine background and combustion noise and pre-
detonation noise.
A basic approach to engine pre-detonation systems is to
only observe engine background during the time interval
that noise is expected and if detected, retard timing. This
basic approach does not require the sensitivity and
selectivity that is needed for a continuously adjustable
solution. Enhanced fuel economy and performance is
obtainable when this IC is coupled with a microprocessor
controlled fuel management system.
EXAMPLE CASE USING IDEAL SYSTEM EQUATION
Where:
V
IN
=200mV
P-P
, Continuous AC Signal
G
IN
=1.0, Ratio of R
F
to R
IN
G
PR
=0.190
G
BPF
=2.0 Ideal Gain Value
t
C
=200
μ
s
t
INT
=2ms
G
DSE
=2.0 Ideal Gain Value
V
RESET
=0.125V, Typical Value
INTOUT (Volts) =
200x10
-3
*1* [2 * 0.19 * 0.318 * 2x10
-3
/200x10
-6
*
2]+0.125
=0.4833 + 0.125
=0.608V
INTOUT (Volts) =
V
IN
G
IN
G
BPR
G
PR
1
π
--
t
c
-------
×
×
×
G
DSE
×
V
RESET
+
×
×
When the Input Signal is Present for the Period t
INT
:
FIGURE 3. SIMPLIFIED BLOCK DIAGRAM OF THE HIP9011 IN AN AUTOMOTIVE APPLICATION
V
DD
GND
VMID
INTOUT
SO
SI
CH1IN
CH1FB
CH0FB
CH0IN
0.022
μ
F
MICROPROCESSOR
+5V
A/D
CONVERTER
OSCIN
OSCOUT
4MHz
TRANSDUCERS
HIP9011
TEST
INT/HOLD
CS
SCK
SPI BUS
CH0NI
CH1NI
20pF
20pF
1M
R
in
R
F
R
F
R
in
+5V
HIP9011
相關PDF資料 |
PDF描述 |
|---|---|
| HIP9020 | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AB | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AP | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9021 | Portable Battery Drive/Torque Controller for N-Channel MOSFETs in Motor Control Systems |
| HIP9021IB | Portable Battery Drive/Torque Controller for N-Channel MOSFETs in Motor Control Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP9011ABR4682 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABR4745 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABR4745A | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABR4818 | 制造商:Intersil Corporation 功能描述: |
| HIP9011ABS2667 | 制造商:Intersil Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。