- 您現在的位置：買賣IC網 > PDF目錄1995 > HI3-DAC80V-5 (Intersil)CONV D/A 12BIT OUTPUT AMP 24PDIP PDF資料下載
參數資料
| 型號： | HI3-DAC80V-5 |
| 廠商： | Intersil |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | CONV D/A 12BIT OUTPUT AMP 24PDIP |
| 標準包裝： | 15 |
| 設置時間： | 1.5µs |
| 位數： | 12 |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 雙 ± |
| 工作溫度： | 0°C ~ 75°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 24-PDIP |
| 包裝： | 管件 |
| 輸出數目和類型： | 1 電壓，單極；1 電壓，雙極 |
| 采樣率（每秒）： | 667k |
6
output. Matched switching times and fast switching will
reduce glitches considerably. (Measured as one half the
Product of duration and amplitude.)
Decoupling and Grounding
For best accuracy and high frequency performance, the
grounding and decoupling scheme shown in Figure 1 should
be used. Decoupling capacitors should be connected close
to the HI-DAC80V (preferably to the device pins) and should
be tantalum or electrolytic bypassed with ceramic types for
best high frequency noise rejection.
Reference Supply
An internal 6.3V reference is provided on board the
HI-DAC80V. The voltage (pin 24) is accurate to
±0.8% and
must be connected to the reference input (pin 16) for
specied operation. This reference may be used externally,
provided current drain is limited to 2.5mA. An external buffer
amplier is recommended if this reference is to be used to
drive other system components. Otherwise, variations in the
load driven by the reference will result in gain variations of
the HI-DAC80V. All gain adjustments should be made under
constant load conditions.
Output Voltage Ranges
18
19
20
15
-
+
-VS
+VS
0.01
F
1
F
14
21
22
0.01
F
1
F
24
16
FIGURE 1.
TABLE 2. RANGE CONNECTIONS
RANGE
CONNECT
PIN 15
PIN 17
PIN 19
Unipolar
0 to +5V
18
NC
20
0 to +10V
18
NC
Bipolar
±2.5V
18
20
±5V
18
20
NC
±10V
19
20
15
TABLE 3. GAIN AND OFFSET CALIBRATIONS
UNIPOLAR CALIBRATION
Step 1:
Offset
Turn all bits OFF (11 . . . 1)
Adjust R2 for 0V out
Step 2:
Gain
Turn all bits ON (00 . . . 0)
Adjust R1 for FS - 1 LSB
That is:
4.9988 for 0 to +5V range
9.9976 for 0 to +10V range
BIPOLAR CALIBRATION
Step 1:
Offset
Turn all bits OFF (11 . . . 1)
Adjust R2 for Negative FS
That is:
-10V for
±10V range
-5V for
±5V range
-2.5V for
±2.5V range
Step 2:
Gain
Turn all bits ON (00 . . . 0)
Adjust R1 for Positive FS - 1 LSB
That is:
+9.9951V for
±10V Range
+4.9976V for
±5V Range
+2.4988V for
±2.5V Range
This Bipolar procedure adjusts the output range end points. The
maximum error at zero (half scale) will not exceed the Linearity
Error. See the “Accuracy” Specifications.
18
19
20
15
-
+
6.3K
21
-
+
CONTROL
AMP
3.9
M
R2
+VS
-VS
12.6k
R1
+VS
-VS
2.8M
0.01
F
10k
TO
100k
24
17
16
23
5k
5k
5k
TO
100k
FIGURE 2. HI-DAC80V
HI-DAC80V
相關PDF資料 |
PDF描述 |
|---|---|
| HI3026JCQ | ADC FLASH 8BIT 120MSPS 48-PQFP |
| HI3338KIBZ | IC DAC 8BIT CMOS 16-SOIC |
| HI5628INZ | IC DAC 8BIT 125MSPS DUAL 48-LQFP |
| HI5660IBZ | CONV D/A 8-BIT 125MSPS 28-SOIC |
| HI5662/6IN | ADC DUAL 8-BIT 60MSPS 44-MQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI3-DAC80V-5Z | 制造商:Intersil Corporation 功能描述:IC 12BIT DAC DIP24 |
| HI3-DAC80V-7 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI3-DAC85V-4 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI3-DAC85V-9 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述: |
| HI401 | 功能描述:板機接口霍耳效應/磁性傳感器 HALL IC RoHS:否 制造商:Honeywell 類型:Bipolar Hall-Effect Digital Position Sensor 工作電源電壓:3 V to 24 V 電源電流:3.5 mA 最大輸出電流:20 mA 工作點最小值/最大值:5 G, 55 G 最小/最大釋放點（Brp）:- 55 G, - 5 G 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 |
發布緊急采購，3分鐘左右您將得到回復。