- 您現在的位置：買賣IC網 > PDF目錄370452 > HCPL-788J Isolation Amplifier with Short Circuit and Overload Detection(具有短路和過載保護功能的隔離放大器) PDF資料下載
參數資料
| 型號： | HCPL-788J |
| 元件分類： | 運動控制電子 |
| 英文描述： | Isolation Amplifier with Short Circuit and Overload Detection(具有短路和過載保護功能的隔離放大器) |
| 中文描述： | 隔離放大器短路和過載檢測（具有短路和過載保護功能的隔離放大器） |
| 文件頁數： | 18/20頁 |
| 文件大小： | 277K |
| 代理商： | HCPL-788J |
18
This filter prevents damage from input spikes which
may go beyond the absolute maximum ratings of the
HCPL-788J inputs during ESD and other transient
events. The filter also prevents aliasing of high fre-
quency (above 3 MHz) noise at the sampled input.
Other RC values are certainly OK, but should be
chosen to prevent the input voltage (pin 1) from ex-
ceeding
±
5 V for any conceivable current waveform
in the sense resistor. Remember to account for in-
ductance of the sense resistor since it is possible to
momentarily have tens of volts across even a 1 m
resistor if di/dt is quite large.
Select the sense resistor so that it will have less than
5 V drop when short circuits occur. The ony other
requirement is to shut down the drive before the
sense resistor is damaged or its solder joints melt.
This ensures that the input of the HCPL-788J can not
be damaged by sense resistors going open-circuit.
2.4:
Do I really need an RC filter on the input
What is it for Are other values of R and
C okay
2.5:
How do I ensure that the HCPL-788J is
not
destroyed as a result of short circuit
conditions which cause voltage drops
across
the sense resistor that exceed the
ratings
of the HCPL-788J’s inputs
3. Isolation and Insulation
The momentary (1 minute) withstand voltage is
3500 V rms per UL1577 and CSA Component
Acceptance Notice #5.
These capacitors are to reduce the narrow output
spikes caused by high common mode slew rates. If
your application does not have rapid common mode
voltage changes, these capacitors are not needed.
3.1:
How many volts will the HCPL-788J
withstand
3.2:
What happens if I don’t use the 470 pF
output capacitors Agilent recommends
4. Accuracy
For zero input, the output should ideally be
1
/
2
of
V
REF
. The nominal slope of the input/output relation-
ship is V
REF
divided by 0.504 V. Offset errors change
only the DC input voltage needed to make the output
equal to
1
/
2
of V
REF
. Gain errors change only the
slope of the input/output relationship. For example,
if V
REF
is 4.0 V, the gain should be 7.937 V/V. For
zero input, the output should be 2.000 V. Input offset
voltage of
±
3 mV means the output voltage will be
2.000 V
±
0.003*7.937 or 2.000
±
23.8 mV when the
input is zero. Gain tolerance of
±
5% means that the
slope will be 7.937
±
0.397. Over the full range of
±
3 mV input offset error and
±
5% gain error, the
output voltage will be 2.000
±
25.0 mV when the
input is zero.
4.1:
What is the meaning of the offset errors
and gain errors in terms of the output
相關PDF資料 |
PDF描述 |
|---|---|
| HCPL-810J | PLC Powerline DAA IC |
| HCPL-J314 | 0.4 Amp Output Current IGBT Gate Drive Optocoupler(0.4 放大輸出電流 IGBT門驅動光耦合器) |
| HCPL-J454 | High CMR, High Speed Optocouplers(高CMR，高速光耦合器) |
| HCPL-0454 | High CMR, High Speed Optocouplers(高CMR，高速光耦合器) |
| HCPL-J456 | Intelligent Power Module and Gate Drive Interface Optocouplers(智能功率模塊和門驅動接口光耦合器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCPL-788J#500 | 功能描述:隔離放大器 4.5 - 5.5 SV RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比（最小值）:95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube |
| HCPL-788J/EVAL | 制造商:Avago Technologies 功能描述: |
| HCPL-788J-000E | 功能描述:隔離放大器 4.5 - 5.5 SV RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比（最小值）:95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube |
| HCPL-788J-500E | 功能描述:隔離放大器 4.5 - 5.5 SV RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比（最小值）:95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube |
| HCPL-800J | 功能描述:緩沖器和線路驅動器 PLC Powerline DAA IC RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。