- 您現在的位置：買賣IC網 > PDF目錄370452 > HCPL-788J Isolation Amplifier with Short Circuit and Overload Detection(具有短路和過載保護功能的隔離放大器) PDF資料下載
參數資料
| 型號： | HCPL-788J |
| 元件分類： | 運動控制電子 |
| 英文描述： | Isolation Amplifier with Short Circuit and Overload Detection(具有短路和過載保護功能的隔離放大器) |
| 中文描述： | 隔離放大器短路和過載檢測（具有短路和過載保護功能的隔離放大器） |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 277K |
| 代理商： | HCPL-788J |
16
the load current should have no
impact on the measured voltage.
When laying out a PC board for
the current sensing resistors, a
couple of points should be kept in
mind. The Kelvin connections to
the resistor should be brought
together under the body of the
resistor and then run very close
to each other to the input of the
HCPL-788J; this minimizes the
loop area of the connection and
reduces the possibility of stray
magnetic fields from interfering
with the measured signal. If
the sense resistor is not located
on the same PC board as the
HCPL-788J circuit, a tightly
twisted pair of wires can
accomplish the same thing.
Also, multiple layers of the PC
board can be used to increase
current carrying capacity.
Numerous plated-through vias
should surround each non-Kelvin
terminal of the sense resistor
to help distribute the current
between the layers of the PC
board. The PC board should use
2 or 4 oz. copper for the layers,
resulting in a current carrying
capacity in excess of 20 A.
Making the current carrying
traces on the PC board fairly
large can also improve the sense
resistor’s power dissipation
capability by acting as a heat
sink. Liberal use of vias where the
load current enters and exits the
PC board is also recommended.
Sense Resistor Connections
The recommended method for
connecting the HCPL-788J to the
current sensing resistor is shown
in Figure 26. V
IN+
(pin 1 of the
HCPL-788J) is connected to the
positive terminal of the sense
resistor, while V
IN-
(pin 2) is
shorted to GND
1
(pin 8), with
the power-supply return path
functioning as the sense line
to the negative terminal of the
current sense resistor. This
allows a single pair of wires or
PC board traces to connect the
HCPL-788J circuit to the sense
resistor. By referencing the input
circuit to the negative side of the
sense resistor, any load current
induced noise transients on the
resistor are seen as a common-
mode signal and will not interfere
with the current-sense signal.
This is important because the
large load currents flowing
through the motor drive, along
with the parasitic inductances
inherent in the wiring of the
circuit, can generate both noise
spikes and offsets that are rela-
tively large compared to the small
voltages that are being measured
across the current sensing resistor.
If the same power supply is used
both for the gate drive circuit
and for the current sensing
circuit, it is very important that
the connection from GND
1
of the
HCPL-788J to the sense resistor
be the only return path for supply
current to the gate drive power
supply in order to eliminate
potential ground loop problems.
The only direct connection
between the HCPL-788J circuit
and the gate drive circuit should
be the positive power supply line.
Please refer to Agilent
Applications Note 1078 for
additional information on using
Isolation Amplifiers.
相關PDF資料 |
PDF描述 |
|---|---|
| HCPL-810J | PLC Powerline DAA IC |
| HCPL-J314 | 0.4 Amp Output Current IGBT Gate Drive Optocoupler(0.4 放大輸出電流 IGBT門驅動光耦合器) |
| HCPL-J454 | High CMR, High Speed Optocouplers(高CMR，高速光耦合器) |
| HCPL-0454 | High CMR, High Speed Optocouplers(高CMR，高速光耦合器) |
| HCPL-J456 | Intelligent Power Module and Gate Drive Interface Optocouplers(智能功率模塊和門驅動接口光耦合器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCPL-788J#500 | 功能描述:隔離放大器 4.5 - 5.5 SV RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比（最小值）:95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube |
| HCPL-788J/EVAL | 制造商:Avago Technologies 功能描述: |
| HCPL-788J-000E | 功能描述:隔離放大器 4.5 - 5.5 SV RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比（最小值）:95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube |
| HCPL-788J-500E | 功能描述:隔離放大器 4.5 - 5.5 SV RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比（最小值）:95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube |
| HCPL-800J | 功能描述:緩沖器和線路驅動器 PLC Powerline DAA IC RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。