- 您現在的位置：買賣IC網 > PDF目錄385355 > HC5549 (Intersil Corporation) Low Power SLIC with Battery Switch(用戶線接口電路) PDF資料下載
參數資料
| 型號： | HC5549 |
| 廠商： | Intersil Corporation |
| 英文描述： | Low Power SLIC with Battery Switch(用戶線接口電路) |
| 中文描述： | 低功耗用戶接口與電池開關（用戶線接口電路） |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 125K |
| 代理商： | HC5549 |
4-6
4-WIRE TO 2-WIRE GAIN
The 4-wire to 2-wire gain is defined as the receive gain. It is
a function of the terminating impedance, synthesized
impedance and protection resistors. Equation 6 calculates
the receive gain, G
42
.
When the device source impedance and protection resistors
equals the terminating impedance, the receive gain equals
unity.
2-WIRE TO 4-WIRE GAIN
The 2-wire to 4-wire gain (G
24
) is the gain from tip and ring to
the VTX output. The transmit gain is calculated in Equation 7.
When the protection resistors are set to zero, the transmit
gain is -6dB.
TRANSHYBRID GAIN
The transhybrid gain is defined as the 4-wire to 4-wire gain
(G
44
).
When the protection resistors are set to zero, the transhybrid
gain is -6dB.
COMPLEX IMPEDANCE SYNTHESIS
Substituting the impedance programming resistor, R
S
, with a
complex programming network provides complex
impedance synthesis.
The reference designators in the programming network
match the evaluation board. The component R
S
has a
different design equation than the R
S
used for resistive
impedance synthesis. The design equations for each
component are provided below.
Low Power Standby
Overview
The low power standby mode (LPS, 000) should be used
during idle line conditions. The device is designed to operate
from the high battery during this mode. Most of the internal
circuitry is powered down, resulting in low power dissipation.
If the 2-wire (tip/ring) DC voltage requirements are not
critical during idle line conditions, the device may be
operated from the low battery. Operation from the low
battery will decrease the standby power dissipation.
2-WIRE INTERFACE
During LPS, the 2-wire interface is maintained with internal
switches and voltage references. The Tip and Ring
amplifiers are turned off to conserve power. The device will
provide MTU compliance, loop current and loop supervision.
Figure 2 represents the internal circuitry providing the 2-wire
interface during low power standby.
MTU Compliance
Maintenance Termination Unit or MTU compliance places
DC voltage requirements on the 2-wire terminals during idle
line conditions. The minimum idle voltage is 42.75V. The
high side of the MTU range is 56V. The voltage is expressed
as the difference between Tip and Ring.
The Tip voltage is held near ground through a 600
resistor
and switch. The Ring voltage is limited to a maximum of
-49V (by MTU REF) when operating from either the high or
Z
O
Z
L
2R
P
–
=
(EQ. 5)
G
42
2
Z
O
P
L
-----------------------------------------
–
=
(EQ. 6)
G
24
Z
O
P
L
-----------------------------------------
–
=
(EQ. 7)
G
44
Z
P
O
L
+
--------+
–
=
(EQ. 8)
FIGURE 1. COMPLEX PROGRAMMING NETWORK
2-WIRE
NETWORK
C
2
R
1
R
2
PROGRAMMING
NETWORK
C
P
R
S
R
P
R
S
400
R
1
2 R
P
)
–
(
)
×
=
(EQ. 9)
R
P
400
R
2
×
=
(EQ. 10)
TABLE 1. DEVICE INTERFACES DURING LPS
INTERFACE
ON
OFF
NOTES
Receive
x
AC transmission, impedance
matching
and
disabled during this mode.
ringing
are
Ringing
x
Transmit
x
2-Wire
x
Amplifiers disabled.
Loop Detect
x
Switch hook or ground key.
C
P
C
2
400
=
(EQ. 11)
FIGURE 2. LPS 2-WIRE INTERFACE CIRCUIT DIAGRAM
TIP AMP
RING AMP
TIP
RING
MTU REF
GND
600
600
HC5549
相關PDF資料 |
PDF描述 |
|---|---|
| HC573 | Octal 3-State Noninverting Transparent Latch(High-Performance Silicon-Gate CMOS) |
| HC595 | 8-Bit Serial-Input/Serial or Parallel-Output Shift Register with Latched 3-State Outputs |
| HC652 | EPROM IC; Memory Size:128Kbit; Memory Configuration:16K x 8; Access Time, Tacc:250ns; Package/Case:28-DIP; EPROM Type:Parallel UV Erasable; Supply Voltage Nom, Vcc:5V; Mounting Type:Through Hole; Voltage Rating:5V |
| HC74 | T-NPN-SI PWR AMP |
| HCA10008 | Darlington Bipolar Transistor; Package/Case:TO-3; Mounting Type:Through Hole; Current Rating:50A; Voltage Rating:120V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC5549_04 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power SLIC with Battery Switch |
| HC5549CM | 制造商:Rochester Electronics LLC 功能描述: |
| HC5549CMZ | 制造商:Intersil Corporation 功能描述:SLIC 1CH 59DB 45MA 5V 28PLCC - Rail/Tube |
| HC5549IM | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power SLIC with Battery Switch |
| HC5552 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。