- 您現在的位置：買賣IC網 > PDF目錄370428 > HB288016MM1 (Hitachi,Ltd.) MultiMediaCard 16 MByte PDF資料下載
參數資料
| 型號： | HB288016MM1 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | MultiMediaCard 16 MByte |
| 中文描述： | 多媒體16字節 |
| 文件頁數： | 31/79頁 |
| 文件大?。?/td> | 233K |
| 代理商： | HB288016MM1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁
HB288016MM1
31
bits do not match the corresponding bits on the command line in any one of the bit periods, stop sending
their CID immediately and must wait for the next identification cycle (cards stay in the Ready State).
There should be only one card which successfully sends its full CID-number to the host. This card then
goes into the Identification State. The host assigns to this card (using CMD3, SET_RELATIVE_ADDR) a
relative card address (RCA, shorter than CID), which will be used to address the card in future
communication (faster than with the CID). Once the RCA is received the card transfers to the Standby
State and does not react to further identification cycles. The card also switches the output drivers from the
open-drain to the push-pull mode in this state. The host repeats the identification process as long as it
receives a response (CID) to its identification command (CMD2). When no card responds to this
command, all cards have been identified. The time-out condition to recognize this, is waiting for the start
bit for more than 5 clock periods after sending CMD2.
Operating Voltage Range Validation
The MultiMediaCard standards operating range validation is intended to support reduced voltage range
MultiMediaCards. The HB288016MM1 supports the range of 2.7 V to 3.6V supply voltage. So the
HB288016MM1 sends a R3 response to CMD1 which contains an OCR value of 0x80FF8000 if the busy
flag is set to “ready” or 0x00FF8000 if the busy flag is active (refer to Chapter “Responses”). By omitting
the voltage range in the command, the host can query the card stack and determine the common voltage
range before sending out-of-range cards into the Inactive State. This bus query should be used if the host is
able to select a common voltage range or if a notification to the application of non usable cards in the stack
is desired. Afterwards, the host must choose a voltage for operation and reissue CMD1 with this condition,
sending incompatible cards into the Inactive State.
相關PDF資料 |
PDF描述 |
|---|---|
| HB288096C5 | CompactFlash(閃速CompactFlash 卡) |
| HB288160C5 | CompactFlash(閃速CompactFlash 卡) |
| HB2881000A5 | FLASH ATA Card 1 GByte |
| HB2881000A6 | FLASH ATA Card |
| HB288160A5 | FLASH ATA Card |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HB288032A5 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288032A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288032C5 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288032C6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288032MM1 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:MultiMediaCard 32 MByte |
發布緊急采購，3分鐘左右您將得到回復。