- 您現在的位置：買賣IC網 > PDF目錄370428 > HB288016MM1 (Hitachi,Ltd.) MultiMediaCard 16 MByte PDF資料下載
參數資料
| 型號： | HB288016MM1 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | MultiMediaCard 16 MByte |
| 中文描述： | 多媒體16字節 |
| 文件頁數： | 30/79頁 |
| 文件大?。?/td> | 233K |
| 代理商： | HB288016MM1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁
HB288016MM1
30
Card identification mode
All the data communication in the card identification mode uses only the command line (CMD).
Idle state
(idle)
CMD0
CMD15
CMD1
Inactive state
(ina)
Ready state
(ready)
CMD2
Indentification state
(ident)
CMD3
Stand-by state
(stby)
card wins bus
from all states except (ina)
from all states in data-transfer mode
Power on
card looses bus
card is busy or
host omitted
voltage range
cards with non-compatible voltage range
data-transfer mode
card-indentification mode
MultiMediaCard State Diagram
(Card Identification Mode)
The host starts the card identification process in open drain mode with the identification clock rate f
OD
(generated by a push pull driver stage). The open drain driver stages on the CMD line allow the parallel
card operation during card identification. After the bus is activated the host will request the cards to send
their valid operation conditions with the command SEND_OP_COND (CMD1). Since the bus is in open
drain mode, as long as there is more than one card with operating conditions restrictions, the host gets in
the response to the CMD1 a “wired or” operation condition restrictions of those cards. The host then must
pick a common denominator for operation and notify the application that cards with out of range
parameters (from the host perspective) are connected to the bus. Incompatible cards go into Inactive State
(refer to also Chapter “Operating Voltage Range Validation”). The busy bit in the CMD1 response can be
used by a card to tell the host that it is still working on its power-up/reset procedure (e.g. downloading the
register information from memory field) and is not ready yet for communication. In this case the host must
repeat CMD1 until the busy bit is cleared. After an operating mode is established, the host asks all cards
for their unique card identification (CID) number with the broadcast command ALL_SEND_CID (CMD2).
All not already identified cards (i.e. those which are in Ready State) simultaneously start sending their CID
numbers serially, while bit-wise monitoring their outgoing bitstream. Those cards, whose outgoing CID
相關PDF資料 |
PDF描述 |
|---|---|
| HB288096C5 | CompactFlash(閃速CompactFlash 卡) |
| HB288160C5 | CompactFlash(閃速CompactFlash 卡) |
| HB2881000A5 | FLASH ATA Card 1 GByte |
| HB2881000A6 | FLASH ATA Card |
| HB288160A5 | FLASH ATA Card |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HB288032A5 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288032A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288032C5 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288032C6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288032MM1 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:MultiMediaCard 32 MByte |
發布緊急采購，3分鐘左右您將得到回復。