參數資料
型號： GS832418C-250
廠商： GSI TECHNOLOGY
元件分類： DRAM
英文描述： 2M x 18, 1M x 36, 512K x 72 36Mb S/DCD Sync Burst SRAMs
中文描述： 2M X 18 CACHE SRAM, 6 ns, PBGA209
封裝： 14 X 22 MM, 1 MM PITCH, BGA-209
文件頁數： 33/46頁
文件大?。?/td> 1149K
代理商： GS832418C-250
Rev: 1.00 10/2001
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
33/46
2001, Giga Semiconductor, Inc.
Preliminary
GS832418(B/C)/GS832436(B/C)/GS832472(C)
Disabling the JTAG Port
It is possible to use this device without utilizing the JTAG port. The port is reset at power-up and will remain inactive unless
clocked. TCK, TDI, and TMS are designed with internal pull-up circuits.To assure normal operation of the RAM with the JTAG
Port unused, TCK, TDI, and TMS may be left floating or tied to either V
DD
or V
SS
. TDO should be left unconnected.
JTAG Port Registers
Overview
The various JTAG registers, refered to as Test Access Port orTAP Registers, are selected (one at a time) via the sequences of 1s
and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the
rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the
TDI and TDO pins.
Instruction Register
The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or
the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the
TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the
controller is placed in Test-Logic-Reset state.
Bypass Register
The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through
the RAM’s JTAG Port to another device in the scan chain with as little delay as possible.
Boundary Scan Register
The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM’s input or I/O pins.
The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port’s TDO pin. The
Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the
device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan
Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in
JTAG Pin Descriptions
Pin
Pin Name
I/O
Description
TCK
Test Clock
In
Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate
from the falling edge of TCK.
The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP
controller state machine. An undriven TMS input will produce the same result as a logic one input
level.
The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers
placed between TDI and TDO. The register placed between TDI and TDO is determined by the
state of the TAP Controller state machine and the instruction that is currently loaded in the TAP
Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce
the same result as a logic one input level.
Output that is active depending on the state of the TAP state machine. Output changes in
response to the falling edge of TCK. This is the output side of the serial registers placed between
TDI and TDO.
TMS
Test Mode Select
In
TDI
Test Data In
In
TDO
Test Data Out
Out
Note:
This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is
held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up.
相關PDF資料
PDF描述
GS832418C-250I 2M x 18, 1M x 36, 512K x 72 36Mb S/DCD Sync Burst SRAMs
GS832436B-133 2M x 18, 1M x 36, 512K x 72 36Mb S/DCD Sync Burst SRAMs
GS832436B-133I 2M x 18, 1M x 36, 512K x 72 36Mb S/DCD Sync Burst SRAMs
GS832436B-150 2M x 18, 1M x 36, 512K x 72 36Mb S/DCD Sync Burst SRAMs
GS832436B-150I 2M x 18, 1M x 36, 512K x 72 36Mb S/DCD Sync Burst SRAMs
相關代理商/技術參數
參數描述
GS8324Z36B-133 制造商:GSI Technology 功能描述:SRAM SYNC QUAD 2.5V/3.3V 36MBIT 1MX36 10NS/4NS 119FBGA - Trays
GS8324Z36B-200I 制造商:GSI Technology 功能描述:SRAM SYNC QUAD 2.5V/3.3V 36MBIT 1MX36 7.5NS/3NS 119FBGA - Trays
GS8324Z72C200 制造商:G.S.I. 功能描述:
GS8342D06BD-350 制造商:GSI Technology 功能描述:165 FBGA - Bulk
GS8342D06BD-500 制造商:GSI Technology 功能描述:165 FBGA - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*