- 您現在的位置：買賣IC網 > PDF目錄370311 > GCIXF1002EDT Controller Miscellaneous - Datasheet Reference PDF資料下載
參數資料
| 型號： | GCIXF1002EDT |
| 英文描述： | Controller Miscellaneous - Datasheet Reference |
| 中文描述： | 控制器雜項-數據表參考 |
| 文件頁數： | 62/128頁 |
| 文件大小： | 1262K |
| 代理商： | GCIXF1002EDT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Intel
IXF1002 Dual Port Gigabit Ethernet Controller
62
Datasheet
4.1.3
FIFO Status Signaling
The IXF1002 reports the status of each FIFO through dedicated signals. Each transmit FIFO has a
txrdy signal indicating that there is enough free space to load new data. Each receive FIFO has a
rxrdy signal indicating that there is enough data to be transferred onto the IX Bus. The txrdy signals
are driven by the IXF1002 only when the txctl_l signal is asserted. The rxrdy signals are enabled by
the rxclt_l signal.The txrdy signal of a specific port is deasserted when the txsel_l signal is asserted
and the specific port is selected (fps). The same applies for the rxrdy signal of a specific port,
which is deasserted with rxsel_l assertion and the specific port selection (fps).
4.2
Packet Transmission
The following sections describe the packet transmission policy.
Note:
The signal naming below refers to the Full-64 IX Bus mode. Signal names should be changed in
accordance to the bus mode as described in
Section 4.1.1.1
and
Section 4.1.1.2
.
4.2.1
Packet Loading
The IXF1002 loads packets from the IX Bus into the transmit FIFO during burst accesses. In order
to guarantee a minimal amount of data transfer, the transmit FIFO txrdy signal reports minimal
space availability according to a programmable threshold (FFO_TSHD<TTH>).
When a new packet is loaded on the FIFO, the first cycle of the first burst must be signalled with
sop signal assertion. If TX_RX_PARAM<CRCD> is set or if the txasis signal is asserted together
with the sop signal, the packet will be sent onto the network without padding or CRC addition. In
this case, it is assumed by the IXF1002 that the CRC is valid and it will not be checked.
At the end of a packet load, the last data must be signalled with the assertion of the eop signal in the
last cycle of the last burst. If the txerr signal is asserted together with eop, the GMII error signal terr
will be asserted or a symbol error will be generated (GPCS mode) in the last data byte of the packet
sent onto the network. The CRC will be damaged if it was requested to be appended by the
IXF1002.
Note:
In case of VLAN tag append, strip or replace, the frame check sequence (FCS) field will be
calculated by the IXF1002 (see
Section 4.2.2.1
).
The IXF1002 may be programmed to handle only a single packet at a time
(TX_RX_PARAM<SPM>).
Byte masking signals (fbe_l[7:0]) may be used to load selective bytes. They can be used during packet
transfer to load packet segments on byte boundaries and for loading the exact number of bytes at the
end of a packet. Valid bytes may start at any byte boundary, while all valid bytes, in a given cycle, need
to be contiguous.
For example, a packet may be built up from the following buffers, with each one being transferred
in a different burst:
相關PDF資料 |
PDF描述 |
|---|---|
| GCIXF440AC | Controller Miscellaneous - Datasheet Reference |
| GCIXF440ACT | Controller Miscellaneous - Datasheet Reference |
| GCIXP1250-166 | Microprocessor |
| GCIXP1250-200 | Microprocessor |
| GCIXP1250-232 | Microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GCIXF1012EC.A3-884560 | 功能描述:IC ETHERNET MAC 12PORT 672-BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| GCIXF1012ECA3 | 制造商:Cortina Systems Inc 功能描述: 制造商:Intel 功能描述: |
| GCIXF1024EC.A3-884561 | 功能描述:IC ETHERNET MAC 24PORT 672-BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| GCIXF18104EE-B0 | 制造商:Cortina Systems Inc 功能描述: |
| GCIXF18201ECB1 | 制造商:Intel 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。