- 您現在的位置：買賣IC網 > PDF目錄375713 > FA13842 (FUJI ELECTRIC HOLDINGS CO., LTD.) CMOS IC(For Switching Power Supply Control) PDF資料下載
參數資料
| 型號： | FA13842 |
| 廠商： | FUJI ELECTRIC HOLDINGS CO., LTD. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | CMOS IC(For Switching Power Supply Control) |
| 中文描述： | CMOS集成電路開關電源控制（對） |
| 文件頁數： | 9/15頁 |
| 文件大?。?/td> | 151K |
| 代理商： | FA13842 |
FA13842, 13843, 13844, 13845
9
5. Output stage
An output stage of CMOS inverter composition is incorporated,
thereby making it possible to fully swing the gate voltage of a
power MOSFET to the V
CC
.
The output stage provides a source current of 400mA and a
sink current of 1A as the peak current capacity. (When V
CC
is
15V)
The output stage is held in the “Low” state in standby mode.
6. Reference voltage
The 5.0V(
±
5%) bandgap reference(Tj=25C) is built-in.
It is possible to supply a current of about 10mA to an external
circuit in addition to supplying a charge current to the timing
capacitor of the oscillator. (See characteristic curve on page
46.)
Connect a ceramic bypass capacitor of 0.1
μ
F or higher to the
VREF terminal to stabilize this voltage.
I
Design advice
1. Start-up circuit
A typical start-up circuit is shown in Fig. 4.
The AC INPUT voltage charges capacitor C2 and supplies
start-up current to the IC through start-up resistance R1. When
this voltage reaches the ON threshold voltage, the IC reverts to
the operation mode and electric power is supplied from the
bias winding of the transformer thereafter.
Using CMOS process, the start-up current is less than 30
μ
A.
When the start-up resistance is increased, the charging rate of
capacitor C2 decreases and start-up time increases. Select
the optimum values for R1 and C2.
The relation between the start-up resistance and start-up time
for the circuit indicated in Fig. 4 is shown in Fig. 5.
Fig. 6 indicates a method to increase the start-up resistance to
reduce loss and shorten start-up time. The start-up time is
shortened by reducing the capacitance of C2. The bias current
is supplied from C3 after start-up.
2. Synchronized operation with external signals
The circuit shown in Fig. 7 allows synchronized operation with
external signals.
Synchronized operation is started when the RT/CT terminal
voltage is raised to about 3V or higher. (Synchronized at
leading edge.)
The external synchronizing signal should be higher than the
free-run frequency.
In the case of FA13844/45, the output frequency of the OUT
terminal is 1/2 that of the synchronizing signal frequency.
Fig. 5 Start-up time
4
3
2
S
1
00
200
400
Start-up resistance R1 (k
)
600
C2=47
μ
F
C2=10
μ
F
800
1000
1200
C2=22
μ
F
Input:100V AC
Fig. 7
+
D3
R2
ER AMP
2R
1R
Synchronized
C4
OSC
REF
5
1
2
4
R
T
C
T
8
~
+
~
DB
R1
D1
C2
MOSFET
Rs
6
7
FA13842
+
C1
T1
AC INPUT
+
Fig. 4
Fig. 6
D2
R1
D1
C2
FA13842
+
C3
+
6
7
相關PDF資料 |
PDF描述 |
|---|---|
| FA13842N | CMOS IC(For Switching Power Supply Control) |
| FA13842P | CMOS IC(For Switching Power Supply Control) |
| FA13843N | CMOS IC(For Switching Power Supply Control) |
| FA13843P | CMOS IC(For Switching Power Supply Control) |
| FA13844N | CMOS IC(For Switching Power Supply Control) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FA13842_05 | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:FUJI SWITCHING POWER SUPPLYCONTROL IC |
| FA13842N | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:CMOS IC(For Switching Power Supply Control) |
| FA13842N-D1 | 制造商:Fuji Electric 功能描述: |
| FA13842P | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:CMOS IC(For Switching Power Supply Control) |
| FA13842P-D1 | 制造商:Fuji Electric 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。