- 您現在的位置：買賣IC網 > PDF目錄375713 > FA13842 (FUJI ELECTRIC HOLDINGS CO., LTD.) CMOS IC(For Switching Power Supply Control) PDF資料下載
參數資料
| 型號： | FA13842 |
| 廠商： | FUJI ELECTRIC HOLDINGS CO., LTD. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | CMOS IC(For Switching Power Supply Control) |
| 中文描述： | CMOS集成電路開關電源控制（對） |
| 文件頁數： | 8/15頁 |
| 文件大小： | 151K |
| 代理商： | FA13842 |
FA13842, 13843, 13844, 13845
8
I
Description of each circuit
1. Oscillator
The oscillation frequency is determined by timing resistance R
T
and timing capacitor C
T
, which are connected to RT/CT
terminal. C
T
is charged to about 3V through R
T
from a 5V
reference, and discharged to about 1.4V by the built-in
discharge circuit. (See Fig. 1, 2, 3.)
Blanking pulses are generated in the IC during the C
T
discharge period.
The output is fixed in the “l(fā)ow” state by these pulses, and a
fixed dead time is produced. See the characteristic curves on
page 45 for the oscillation frequency, R
T
and C
T
.
In the case of FA13844/45, a flip-flop causes the output to be
blanked with every other cycle. Therefore, the switching
frequency of a power MOSFET is 1/2 of the oscillation
frequency determined by R
T
and C
T
. (See Fig. 3.)
2. Error amplifier
Inverting input and output are connected to the FB terminal
and COMP terminal, respectively. A 2.5V reference is
connected internally to the non-inverting input.
The output voltage is offset by a diode V
F
voltage (=0.7V) and
divided by three. The divided voltage is connected to the input
of the current sensing comparator.
3. Current sensing comparator and PWM latch
The “High” state of the OUT terminal begins at the time C
T
starts charging. The OUT terminal turns to “Low” when the
peak inductor current reaches the threshold level controlled by
the error amplifier output (COMP terminal).
The inductor current is converted to a voltage by sensing
resistor R
S
inserted between GND and the source of a power
MOSFET. This voltage is monitored by the ISNS terminal.
The peak current of inductor “Ipk” is expressed as follows:
Ipk=(Vcomp–0.7) / (3R
S
)
Vcomp: a voltage on COMP terminal
0.7V V
F
The maximum value of the threshold level of the current
sensing comparator is held to 1V. Therefore, the maximum
peak current “Ipk(max)” is as follows:
Ipk(max)=1.0V/R
S
4. Undervoltage lockout (UVLO)
In order to set the IC in the operation mode before the output
stage(OUT terminal) is enabled, two under-voltage lockout
comparators are incorporated to monitor the power supply
voltage (V
CC
) and reference voltage (V
REF
).
The threshold level of the V
CC
comparator is set at 16.5V/9V for
FA13842/44 and 9.6V/9V for FA13843/45. In the standby
mode, in which the V
CC
is under ON threshold, the power
supply current is maintained at nearly 0 (zero). However, a
maximum current of 30
μ
A is required to change from standby
mode to operating mode .
The threshold level of the V
REF
comparator is set at about 3.2V/
2.0V.
A 30V zener diode is connected to V
CC
and GND to protect the
IC against overvoltages.
Fig. 1
Fig. 2 FA13842, 13843
Fig. 3 FA13844, 13845
ENB
OUTPUT
UVLO
UVLO
VCC
ENB
2.5V
5V REF
OSC
30V
RT/CT
FB
COMP
ISNS
VREF
8
OUT
GND
2R
RS
M
1R
1V
S
FFQ
QB
R
Vcc
Vin
VCC
ER AMP
R
T
C
T
7
4
2
1
3
5
6
3V
1.4V
CT
Set
COMP
ISENS
Reset
OUT
3V
1.4V
CT
Set
COMP
ISENS
Reset
OUT
相關PDF資料 |
PDF描述 |
|---|---|
| FA13842N | CMOS IC(For Switching Power Supply Control) |
| FA13842P | CMOS IC(For Switching Power Supply Control) |
| FA13843N | CMOS IC(For Switching Power Supply Control) |
| FA13843P | CMOS IC(For Switching Power Supply Control) |
| FA13844N | CMOS IC(For Switching Power Supply Control) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FA13842_05 | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:FUJI SWITCHING POWER SUPPLYCONTROL IC |
| FA13842N | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:CMOS IC(For Switching Power Supply Control) |
| FA13842N-D1 | 制造商:Fuji Electric 功能描述: |
| FA13842P | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:CMOS IC(For Switching Power Supply Control) |
| FA13842P-D1 | 制造商:Fuji Electric 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。