- 您現在的位置：買賣IC網 > PDF目錄375705 > F49L160UA-90T (ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC) 16 Mbit (2M x 8/1M x 16) 3V Only CMOS Flash Memory PDF資料下載
參數資料
| 型號： | F49L160UA-90T |
| 廠商： | ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC |
| 元件分類： | DRAM |
| 英文描述： | 16 Mbit (2M x 8/1M x 16) 3V Only CMOS Flash Memory |
| 中文描述： | 1M X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| 封裝： | 12 X 20 MM, TSOP1-48 |
| 文件頁數： | 10/51頁 |
| 文件大小： | 454K |
| 代理商： | F49L160UA-90T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
ES MT
Output Disable Mode
With the
OE
is at a logic high level (V
IH
), outputs from
the devices are disabled. This will cause the output pins
in a high impedance state
Standby Mode
When
CE
and
ESET
R
are both held at V
CC
± 0.3V,
the device enter CMOS Standby mode. If
CE
and
are held at V
IH
, but not within the range of
V
CC
± 0.3V, the device will still be in the standby mode,
but the standby current will be larger.
If the device is deselected during auto algorithm of
erasure or programming, the device draws active
current I
CC2
until the operation is completed. I
CC3
in
the DC Characteristics table represents the standby
current specification.
The device requires standard access time (t
CE
) for
read access from either of these standby modes,
before it is ready to read data.
Sector Protect / Un-protect Mode
The hardware sector protect feature disables both
program and erase operations in any sector. The
hardware sector unprotect feature re-enables both the
program and erase operations in previously protected
sectors. Sector protect/unprotect can be implemented
via two methods.
The primary method requires V
ID
on the
only, and can be implemented either in-system or via
programming equipment.
7.2 Software Command Definitions
F49L160UA/F49L160BA
Elite Semiconductor Memory Technology Inc.
Publication Date : Dec. 2006
Revision: 1.3 10/51
ESET
R
ESET
R
pin
Figure 16 shows the algorithms and Figure 15 shows
the timing diagram. This method uses standard
microprocessor bus cycle timing. For sector unprotect,
all unprotected sectors must first be protected prior to
the first sector unprotect write cycle.
The alternate method intended only for programming
equipment requires V
ID
on address pin A9,
OE
, and
ESET
R
.
Auto-select Mode
The auto-select mode provides manufacturer and
device identification and sector protection verification,
through outputs on DQ7–DQ0. This mode is primarily
intended for programming equipment to automatically
match a device to be programmed with its
corresponding programming algorithm. However, the
auto-select codes can also be accessed in-system
through the command register.
When using programming equipment, this mode
requires V
ID
(10 V to 10.5 V) on address pin A9. While
address pins A3, A2, A1, and A0 must be as shown in
Table 4.
To verify sector protection, all necessary pins have to
be set as required in Table 4, the programming
equipment may then read the corresponding identifier
code on DQ7-DQ0.
To access the auto-select codes in-system, the host
system can issue the auto-select command via the
command register, as shown in Table 5. This method
does not require V
ID
. See “ Software Command
Definitions” for details on using the auto-select mode.
Writing specific address and data commands or
sequences into the command register initiates the
device operations. Table 5 defines the valid register
command sequences. Writing incorrect address and
data values or writing them in the improper sequence
resets the device to reading array data.
All addresses are latched on the falling edge of
WE
or
CE
, whichever happens later. All data is latched on
the rising edge of
WE
or
CE
, whichever happens
first. Refer to the corresponding timing diagrams in
the AC Characteristics section.
相關PDF資料 |
PDF描述 |
|---|---|
| F49L400BA | 4 Mbit (512K x 8/256K x 16) 3V Only CMOS Flash Memory |
| F49L400BA-70T | 4 Mbit (512K x 8/256K x 16) 3V Only CMOS Flash Memory |
| F49L400BA-90T | 4 Mbit (512K x 8/256K x 16) 3V Only CMOS Flash Memory |
| F49L400UA | 4 Mbit (512K x 8/256K x 16) 3V Only CMOS Flash Memory |
| F49L400UA-70T | 4 Mbit (512K x 8/256K x 16) 3V Only CMOS Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| F49L160UA-90TG | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:16 Mbit (2M x 8/1M x 16) 3V Only CMOS Flash Memory |
| F49L160UA-90TIG | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:16 Mbit (2M x 8/1M x 16) 3V Only CMOS Flash Memory |
| F49L320BA | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:32 Mbit (4M x 8/2M x 16) 3V Only CMOS Flash Memory |
| F49L320BA-70TG | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:32 Mbit (4M x 8/2M x 16) 3V Only CMOS Flash Memory |
| F49L320BA-70TIG | 制造商:ESMT 制造商全稱:Elite Semiconductor Memory Technology Inc. 功能描述:32 Mbit (4M x 8/2M x 16) 3V Only CMOS Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。