參數資料
型號： EVAL-ADUC831QSZ
廠商： Analog Devices Inc
文件頁數： 22/76頁
文件大?。?/td> 0K
描述： KIT DEV FOR ADUC831 QUICK START
產品培訓模塊： Process Control
標準包裝： 1
系列： QuickStart™ 套件
類型： MCU
適用于相關產品： ADuC831
所含物品： 評估板、電源、纜線、軟件和說明文檔
產品目錄頁面： 739 (CN2011-ZH PDF)
相關產品： ADUC831BCPZ-ND - IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC831BCPZ-REEL-ND - IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC831BSZ-REEL-ND - IC MCU 62K FLASH ADC/DAC 52MQFP
ADUC831BSZ-ND - IC ADC/DAC 12BIT W/MCU 52-MQFP
其它名稱： EVAL-ADUC831QS
EVAL-ADUC831QS-ND
REV. 0
ADuC831
–29–
USING THE FLASH/EE DATA MEMORY
The 4 kBytes of Flash/EE data memory is configured as 1024
pages, each of four bytes. As with the other ADuC831 peripherals,
the interface to this memory space is via a group of registers mapped
in the SFR space. A group of four data registers (EDATA1–4)
are used to hold the four bytes of data at each page. The page is
addressed via the two registers EADRH and EADRL. Finally,
ECON is an 8-bit control register that may be written with one
of nine Flash/EE memory access commands to trigger various
read, write, erase, and verify functions.
A block diagram of the SFR interface to the Flash/EE data
memory array is shown in Figure 20.
ECON—Flash/EE Memory Control SFR
Programming of either the Flash/EE data memory or the Flash/EE
program memory is done through the Flash/EE memory control
SFR (ECON). This SFR allows the user to read, write, erase, or
verify the 4 kBytes of Flash/EE data memory or the 56 kBytes of
Flash/EE program memory.
BYTE 1
(0000H)
EDATA1
SFR
BYTE 1
(0004H)
BYTE 1
(0008H)
BYTE 1
(000CH)
BYTE 1
(0FF8H)
BYTE 1
(0FFCH)
BYTE 2
(0001H)
EDATA2
SFR
BYTE 2
(0005H)
BYTE 2
(0009H)
BYTE 2
(000DH)
BYTE 2
(0FF9H)
BYTE 2
(0FFDH)
BYTE 3
(0002H)
EDATA3
SFR
BYTE 3
(0006H)
BYTE 3
(000AH)
BYTE 3
(000EH)
BYTE 3
(0FFAH)
BYTE 3
(0FFEH)
BYTE 4
(0003H)
EDATA4
SFR
BYTE 4
(0007H)
BYTE 4
(000BH)
BYTE 4
(000FH)
BYTE 4
(0FFBH)
BYTE 4
(0FFFH)
01H
00H
02H
03H
3FEH
3FFH
PAGE
ADDRESS
(E
ADRH/L)
BYTE
ADDRESSES
ARE GIVEN IN
BRACKETS
Figure 20. Flash/EE Data Memory Control and Configuration
Table VII. ECON—Flash/EE Memory Commands
COMMAND DESCRIPTION
ECON VALUE
(NORMAL MODE) (Power-On Default)
(ULOAD MODE)
01H
Results in 4 bytes in the Flash/EE data memory,
Not Implemented. Use the MOVC instruction.
READ
addressed by the page address EADRH/L, being read
into EDATA1–4.
02H
Results in four bytes in EDATA1–4 being written to
Results in bytes 0-255 of internal XRAM being written
WRITE
the Flash/EE data memory, at the page address given by
to the 256 bytes of Flash/EE program memory at the
EADRH/L (0
≤ EADRH/L < 0400H.
page address given by EADRH. (0
≤ EADRH < E0H)
Note: The four bytes in the page being addressed must
Note: The 256 bytes in the page being addressed must
be pre-erased.
03H
Reserved Command
04H
Verifies if the data in EDATA1–4 is contained in the
Not Implemented. Use the MOVC and MOVX
VERIFY
page address given by EADRH/L. A subsequent read
instructions to verify the WRITE in software.
of the ECON SFR will result in a 0 being read if the
verification is valid, or a nonzero value being read to
indicate an invalid verification.
05H
Results in the Erase of the 4-byte page of Flash/EE data
Results in the 64-byte page of Flash/EE program
ERASE PAGE
memory addressed by the page address EADRH/L.
memory, addressed by the byte address EADRH/L
being erased. EADRL can equal any of 64 locations
within the page. A new page starts whenever EADRL
is equal to 00H, 40H, 80H, or C0H.
06H
Results in the erase of entire 4 kBytes of Flash/EE
Results in the Erase of the entire 56 kBytes of ULOAD
ERASE ALL
data memory.
Flash/EE program memory.
81H
Results in the byte in the Flash/EE data memory,
Not Implemented. Use the MOVC command.
READBYTE
addressed by the byte address EADRH/L, being read
into EDATA1. (0
≤ EADRH/L ≤ 0FFFH).
82H
Results in the byte in EDATA1 being written into
WRITEBYTE
Flash/EE data memory, at the byte address EADRH/L.
Flash/EE program memory, at the byte address
EADRH/L (0
≤ EADRH/L ≤ DFFFH).
0FH
Leaves the ECON instructions to operate on the
Enters NORMAL mode directing subsequent ECON
EXULOAD
Flash/EE data memory.
instructions to operate on the Flash/EE data memory.
F0H
Enters ULOAD mode, directing subsequent ECON
Leaves the ECON instructions to operate on the
ULOAD
instructions to operate on the Flash/EE program memory.
Flash/EE program memory.
相關PDF資料
PDF描述
HMM08DRKI CONN EDGECARD 16POS DIP .156 SLD
0210490856 CABLE JUMPER 1.25MM .051M 17POS
EVAL-ADUC7028QSZ KIT DEV ADUC7028 QUICK START
GMM12DREN CONN EDGECARD 24POS .156 EYELET
GSM12DREH CONN EDGECARD 24POS .156 EYELET
相關代理商/技術參數
參數描述
EVAL-ADUC832QS 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk 制造商:Analog Devices 功能描述:DEVELOPMENT KIT SYSTEM
EVAL-ADUC832QSZ 功能描述:KIT DEV FOR ADUC832 QUICK START RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC834QS 制造商:Analog Devices 功能描述:DATA ACQ SYS, MICROCNVRTR, DUAL 16BIT/24BIT - ADCS W/ EMBEDD - Bulk 制造商:Analog Devices 功能描述:8052 ADUC834 QUICKSTART DEV KIT
EVAL-ADUC834QSZ 功能描述:KIT DEV QUICK START ADUC834 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC836QS 制造商:Analog Devices 功能描述:MCU 8BIT 8052 CISC 62KB+4KB FLASH 3.6V 48LQFP - Bulk 制造商:Analog Devices 功能描述:KIT- ADUC836 DEV SYSTEM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*