- 您現在的位置：買賣IC網 > PDF目錄17061 > EVAL-AD7734EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7734 PDF資料下載
參數資料
| 型號： | EVAL-AD7734EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/32頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7734 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 15.4k |
| 數據接口： | 串行 |
| 輸入范圍： | ±10 V |
| 在以下條件下的電源（標準）： | 85mW @ 5V |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7734 |
| 已供物品： | 板，纜線，CD |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
| 相關產品： | AD7734BRUZ-REEL7TR-ND - IC ADC 24BIT 4CH SIG-DEL 28TSSOP AD7734BRUZ-REEL-ND - IC ADC 24BIT 4CH SIG-DEL 28TSSOP AD7734BRUZ-ND - IC ADC 24BIT 4-CH 28-TSSOP AD7734BRU-ND - IC ADC 24BIT 4-CH 28-TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7734
Data Sheet
Rev. A | Page 30 of 32
I/O PORT
The AD7734 P0 pin can be used as a general-purpose digital
I/O pin. The P1 pin (SYNC/P1) can be used as a general-
purpose digital I/O pin or to synchronize the AD7734 with
other devices in the system. When the SYNC bit in the I/O port
register is set and the SYNC pin is low, the AD7734 does not
process any conversion. If it is put into single conversion mode,
continuous conversion mode, or any calibration mode, the
AD7734 waits until the SYNC pin goes high and then starts
operation. This allows conversion to start from a known point
in time, i.e., the rising edge of the SYNC pin.
The digital P0 and P1 voltage is referenced to the analog
supplies. When configured as inputs, the pins should be tied
high or low.
CALIBRATION
The AD7734 provides zero-scale self-calibration, and zero- and
full-scale system calibration capability that can effectively
reduce the offset error and gain error to the order of the noise.
After each conversion, the ADC conversion result is scaled
using the ADC calibration registers and the relevant channel
calibration registers before being written to the data register.
For unipolar ranges:
Data = ((ADC result – ADC ZS Cal. reg.)
× ADC FS Reg./200000h
– Ch. ZS Cal. reg.)
× Ch. FS Cal. reg./200000h
For bipolar ranges:
Data = ((ADC result – ADC ZS Cal. reg.)
× ADC FS Reg./400000h
+ 800000h – Ch. ZS Cal.
reg.)
× Ch. FS Cal. reg./200000h
Where the ADC result is in the range of 0 to FFFFFFh.
Note that the channel zero-scale calibration register has the
format of a sign bit and a 22-bit channel offset value.
It is strongly recommended that the user not change the ADC
full-scale register.
To start any calibration, write the relevant mode bits to the
AD7734 mode register. After the calibration is complete, the
contents of the corresponding calibration registers are updated,
all RDY bits in the ADC status register are set, the SYNC pin
goes low, and the AD7734 reverts to idle mode. The calibration
duration is the same as the conversion time configured on the
selected channel. A longer conversion time gives less noise and
yields a more exact calibration; therefore, use at least the default
conversion time to initiate any calibration.
ADC ZERO-SCALE SELF-CALIBRATION
The ADC zero-scale self-calibration can reduce the offset error
in the chopping disabled mode. If repeated after a temperature
change, it can also reduce the offset drift error in the chopping
disabled mode.
The zero-scale self-calibration is performed on internally
shorted ADC inputs. The negative analog input terminal on the
selected channel is used to set the ADC zero-scale calibration
common mode. Therefore, either the negative terminal of the
selected differential pair or the AINCOM on the single-ended
channel configuration should be driven to a proper common-
mode voltage.
It is strongly recommended that the ADC zero-scale calibration
register should only be updated as part of a zero-scale self-
calibration.
PER CHANNEL SYSTEM CALIBRATION
If the per channel system calibrations are used, these should be
initiated in the following order: a channel zero-scale system
calibration, followed by a channel full-scale system calibration.
The system calibration is affected by the ADC zero-scale and
full-scale calibration registers. Therefore, if both self-calibration
and system calibration are used in the system, an ADC full-
scale self-calibration should be performed first, followed by a
system calibration cycle.
While executing a system calibration, the fully settled system
zero-scale voltage signal or system full-scale voltage signal must
be connected to the selected channel analog inputs.
The per channel calibration registers can be read, stored, or
modified and written back to the AD7734. Note that when
writing the calibration registers the AD7734 must be in idle
mode. Note that outside the specified calibration range,
calibration is possible but the performance may degrade (see
the System Calibration section in Table 1).
相關PDF資料 |
PDF描述 |
|---|---|
| SK471M100ST | CAP ALUM 470UF 100V 20% RADIAL |
| 0982660774 | CBL 9POS 0.5MM JMPR TYPE D 5" |
| EVAL-AD7794EBZ | BOARD EVALUATION FOR AD7794 |
| VE-B2L-EY | CONVERTER MOD DC/DC 28V 50W |
| DC979A | BOARD DELTA SIGMA ADC LTC2442 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7738EB | 制造商:Analog Devices 功能描述:Evaluation Board For AD7738 ADC 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7738EBZ | 功能描述:BOARD EVAL FOR AD7738 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7739EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7739EBZ | 功能描述:BOARD EVAL FOR AD7739 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7741/42EB | 制造商:Analog Devices 功能描述:Evaluation Board For Single And Multi-Channel Synchronous Voltage-To-Frequency Converters 制造商:Analog Devices 功能描述:EVALUATION BOARD IC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。