- 您現在的位置：買賣IC網 > PDF目錄16992 > EVAL-AD7691CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7691CBZ PDF資料下載
參數資料
| 型號： | EVAL-AD7691CBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7691CBZ |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 18 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 10.6mW @ 250kSPS，5 V |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7691 |
| 已供物品： | 板 |
| 相關產品： | AD7691BCPZRL7TR-ND - IC ADC 18BIT SAR 250KSPS 10LFCSP AD7691BCPZRL-ND - IC ADC 18BIT SAR 250KSPS 10LFCSP AD7691BRMZ-RL7-ND - IC ADC 18BIT SAR 250KSPS 10-MSOP AD7691BRMZ-ND - IC ADC 18BIT SAR 250KSPS 10-MSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Data Sheet
AD7691
Rev. C | Page 17 of 28
AD8031
AD7691
VIO
REF
VDD
10F
1F
10
10k
5V
1F
1
1OPTIONAL REFERENCE BUFFER AND FILTER.
06
14
6-
04
6
POWER SUPPLY
The AD7691 uses two power supply pins: a core supply (VDD) and
a digital input/output interface supply (VIO). VIO allows direct
interface with any logic between 1.8 V and VDD. To reduce the
supplies needed, the VIO and VDD pins can be tied together. The
AD7691 is independent of power supply sequencing between VIO
and VDD. Additionally, it is very insensitive to power supply
variations over a wide frequency range, as shown in Figure 25.
The AD7691 powers down automatically at the end of each
conversion phase, and therefore, the power scales linearly with
the sampling rate. This makes the part ideal for low sampling
rate (as low as a few hertz) and low battery-powered applications.
Figure 34. Example of an Application Circuit
DIGITAL INTERFACE
Though the AD7691 has a reduced number of pins, it offers
flexibility in its serial interface modes.
1000
10
0.1
0.001
10
1M
SAMPLING RATE (SPS)
O
P
E
RAT
ING
C
URRE
NT
(
A
)
100
1k
100k
10k
VDD = 5V
VIO
06
14
6-
04
5
When in CS mode, the AD7691 is compatible with SPI, QSPI,
digital hosts, and DSPs, for example, Blackfin ADSP-BF53x or
ADSP-219x. In this mode, the AD7691 can use either a 3-wire
or 4-wire interface. A 3-wire interface using the CNV, SCK, and
SDO signals minimizes wiring connections and is useful, for
instance, in isolated applications. A 4-wire interface using the
SDI, CNV, SCK, and SDO signals allows CNV, which initiates
the conversions, to be independent of the readback timing
(SDI). This is useful in low jitter sampling or simultaneous
sampling applications.
When in chain mode, the AD7691 provides a daisy-chain
feature using the SDI input for cascading multiple ADCs on a
single data line similar to a shift register.
Figure 33. Operating Current vs. Sample Rate
SUPPLYING THE ADC FROM THE REFERENCE
The mode in which the part operates depends on the SDI level
when the CNV rising edge occurs. The CS mode is selected if
SDI is high, and the chain mode is selected if SDI is low. The
SDI hold time is such that when SDI and CNV are connected
together, the chain mode is selected.
For simplified applications, the AD7691, with its low operating
current, can be supplied directly using the reference circuit
shown in Figure 34. The reference line can be driven by
The system power supply directly.
A reference voltage with enough current output capability, such
as the ADR43x.
In either mode, the AD7691 offers the option of forcing a start
bit in front of the data bits. This start bit can be used as a busy
signal indicator to interrupt the digital host and trigger the data
reading. Otherwise, without a busy indicator, the user must
timeout the maximum conversion time prior to readback.
A reference buffer, such as the AD8031, which can also filter the
system power supply, as shown in Figure 34.
The busy indicator feature is enabled
In the CS mode if CNV or SDI is low when the ADC
conversion ends (see
and
).
In the chain mode if SCK is high during the CNV rising edge
(see Figure 46).
相關PDF資料 |
PDF描述 |
|---|---|
| AD9215BCP-80EBZ | BOARD EVAL FOR AD9215BCP-80 |
| 1499690-7 | AMPTRAC I/O 2MM CABLE 2POS 7FT |
| ISL21010DFH312Z-TK | IC INTERFACE |
| 1499690-4 | AMPTRAC I/O 2MM CABLE 2POS 4FT |
| 1025R-30K | COIL 2.7UH MOLDED UNSHIELDED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7691SDZ | 功能描述:BOARD EVAL FOR AD7691 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7693CB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 16BIT, 0.5 LSB, 500 KSPS PULSARDIFFERENTIAL ADC - Bulk |
| EVAL-AD7693CBZ | 功能描述:BOARD EVALUATION FOR AD7693 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7693SDZ | 功能描述:數據轉換 IC 開發工具 EVAL BOARD 16-bit ADC 500kSPS RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| EVAL-AD7694CB | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。