- 您現在的位置：買賣IC網 > PDF目錄17044 > EVAL-AD7685SDZ (Analog Devices Inc)BOARD EVAL FOR AD7685 PDF資料下載
參數資料
| 型號： | EVAL-AD7685SDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD7685 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 10mW @ 250kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7685 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7685
Rev. C | Page 24 of 28
APPLICATION HINTS
LAYOUT
The printed circuit board (PCB) that houses the AD7685
should be designed so that the analog and digital sections are
separated and confined to certain areas of the board. The
pinout of the AD7685 with all its analog signals on the left side
and all its digital signals on the right side eases this task.
Avoid running digital lines under the device because these
couple noise onto the die, unless a ground plane under the
AD7685 is used as a shield. Fast switching signals, such as CNV
or clocks, should never run near analog signal paths. Crossover
of digital and analog signals should be avoided
At least one ground plane should be used. It could be common
or split between the digital and analog section. In the latter case,
the planes should be joined underneath the AD7685.
The AD7685 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, and ideally right up against, the REF
and GND pins and connected with wide, low impedance traces.
Finally, the power supplies VDD and VIO should be decoupled
with ceramic capacitors, typically 100 nF, placed close to the
AD7685 and connected using short and wide traces to provide
low impedance paths and to reduce the effect of glitches on the
power supply lines.
An example layout following these rules is shown in Figure 46
and Figure 47.
EVALUATING THE PERFORMANCE OF THE AD7685
Other recommended layouts for the AD7690 are outlined in
the documentation of the evaluation board (EVAL-AD7685CB).
The evaluation board package includes a fully assembled and
tested evaluation board, documentation, and software for
controlling the board from a PC via the universal evaluation
control board (EVAL-CONTROL BRD3).
02
96
8-
04
4
Figure 46. Example of Layout of the AD7685 (Top Layer)
0
29
68
-04
5
Figure 47. Example of Layout of the AD7685 (Bottom Layer)
相關PDF資料 |
PDF描述 |
|---|---|
| ADR421ARZ-REEL7 | IC VREF SERIES PREC 2.5V 8-SOIC |
| REC5-483.3SRW/H6/C | CONV DC/DC 5W 36-72VIN 3.3VOUT |
| 0982660899 | CBL 21PS 0.5MM JMPR TYPE A 1.18" |
| PH50S280-15 | DC-DC CONVERTER 50W 15V OUTPUT |
| UPS2F221MRD | CAP ALUM 220UF 315V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7686CB | 制造商:Analog Devices 功能描述: |
| EVAL-AD7686CBZ | 功能描述:BOARD EVALUATION FOR AD7686 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7686SDZ | 功能描述:數據轉換 IC 開發工具 EVAL BOARD 100Ksps/400Ksps 16 bit I.C RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| EVAL-AD7687CB | 制造商:Analog Devices 功能描述:EVAL BOARD 16-BIT, 250KSPS DIFFER . I.C. - Bulk |
| EVAL-AD7687CBZ | 功能描述:BOARD EVALUATION FOR AD7687 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。