參數資料
型號： EVAL-AD7685SDZ
廠商： Analog Devices Inc
文件頁數： 13/28頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD7685
標準包裝： 1
系列： PulSAR®
ADC 的數量： 1
位數： 16
采樣率（每秒）： 250k
數據接口： 串行
輸入范圍： ±VREF
在以下條件下的電源（標準）： 10mW @ 250kSPS
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD7685
已供物品： 板
AD7685
Rev. C | Page 20 of 28
CS MODE 4-WIRE, NO BUSY INDICATOR
This mode is usually used when multiple AD7685s are
connected to an SPI-compatible digital host.
A connection diagram example using two AD7685s is shown in
Figure 38, and the corresponding timing is given in Figure 39.
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback (if SDI and CNV are low, SDO is
driven low). Prior to the minimum conversion time, SDI could
be used to select other SPI devices, such as analog multiplexers,
but SDI must be returned high before the minimum conversion
time and held high until the maximum conversion time to
avoid the generation of the BUSY signal indicator. When the
conversion is complete, the AD7685 enters the acquisition
phase and powers down. Each ADC result can be read by
bringing low its SDI input, which consequently outputs the
MSB onto SDO. The remaining data bits are then clocked by
subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge will allow a faster
reading rate, provided it has an acceptable hold time. After the
16th SCK falling edge, or when SDI goes high, whichever is
earlier, SDO returns to high impedance and another AD7685
can be read.
If multiple AD7685s are selected at the same time, the SDO
output pin handles this contention without damage or induced
latch-up. Meanwhile, it is recommended to keep this contention
as short as possible to limit extra power dissipation.
DATA IN
CLK
CS1
CONVERT
CS2
DIGITAL HOST
02
96
8-
0
3
6
CNV
SCK
SDO
SDI
AD7685
CNV
SCK
SDO
SDI
AD7685
Figure 38. CS Mode 4-Wire, No BUSY Indicator Connection Diagram
SDO
D15
D14
D13
D1
D0
tDIS
SCK
12
3
30
31
32
tHSDO
tDSDO
tEN
CONVERSION
ACQUISITION
tCONV
tCYC
tACQ
ACQUISITION
SDI(CS1)
CNV
tSSDICNV
tHSDICNV
D1
14
15
tSCK
tSCKL
tSCKH
D0
D15
D14
17
18
16
SDI(CS2)
02
96
8-
03
7
Figure 39. CS Mode 4-Wire, No BUSY Indicator Serial Interface Timing
相關PDF資料
PDF描述
ADR421ARZ-REEL7 IC VREF SERIES PREC 2.5V 8-SOIC
REC5-483.3SRW/H6/C CONV DC/DC 5W 36-72VIN 3.3VOUT
0982660899 CBL 21PS 0.5MM JMPR TYPE A 1.18"
PH50S280-15 DC-DC CONVERTER 50W 15V OUTPUT
UPS2F221MRD CAP ALUM 220UF 315V 20% RADIAL
相關代理商/技術參數
參數描述
EVAL-AD7686CB 制造商:Analog Devices 功能描述:
EVAL-AD7686CBZ 功能描述:BOARD EVALUATION FOR AD7686 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7686SDZ 功能描述:數據轉換 IC 開發工具 EVAL BOARD 100Ksps/400Ksps 16 bit I.C RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
EVAL-AD7687CB 制造商:Analog Devices 功能描述:EVAL BOARD 16-BIT, 250KSPS DIFFER . I.C. - Bulk
EVAL-AD7687CBZ 功能描述:BOARD EVALUATION FOR AD7687 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*