- 您現在的位置：買賣IC網 > PDF目錄17039 > EVAL-AD7661CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7661 PDF資料下載
參數資料
| 型號： | EVAL-AD7661CBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7661 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 100k |
| 數據接口： | 串行，并聯 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 16mW @ 100kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7661 |
| 已供物品： | 板，CD |
| 相關產品： | AD7661ACPZRL-ND - IC ADC 16BIT W/REF 48-LFCSP AD7661ASTZ-ND - IC ADC 16BIT W/REF 48-LQFP AD7661ACPZ-ND - IC ADC 16BIT W/REF 48LFCSP AD7661ASTZRL-ND - IC ADC 16BIT W/REF 48LQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7661
Rev. 0 | Page 18 of 28
TYPICAL CONNECTION DIAGRAM
Figure 26 shows a typical connection diagram for the AD7661.
Analog Input
Figure 27 shows an equivalent circuit of the input structure of
the AD7661.
The two diodes, D1 and D2, provide ESD protection for the
analog inputs IN and INGND. Care must be taken to ensure
that the analog input signal never exceeds the supply rails by
more than 0.3 V. This will cause these diodes to become
forward-biased and start conducting current. These diodes can
handle a forward-biased current of 100 mA maximum. For
instance, these conditions could eventually occur when the
input buffer’s (U1) supplies are different from AVDD. In such a
case, an input buffer with a short-circuit current limitation can
be used to protect the part.
C2
R1
D1
D2
C1
IN
OR INGND
AGND
AVDD
03033-0-023
Figure 27. Equivalent Analog Input Circuit
This analog input structure allows the sampling of the differen-
tial signal between IN and INGND. Unlike other converters,
INGND is sampled at the same time as IN. By using this
differential input, small signals common to both inputs are
rejected, as shown in Figure 28 which represents the typical
CMRR over frequency with on-chip and external references.
For instance, by using INGND to sense a remote signal ground,
ground potential differences between the sensor and the local
ADC ground are eliminated.
30
35
40
45
50
55
60
65
70
75
80
1
10
100
1000
10000
FREQUENCY (kHz)
CMRR
(dB)
03033-0-042
EXT REF
REF
Figure 28. Analog Input CMRR vs. Frequency
During the acquisition phase, the impedance of the analog
input IN can be modeled as a parallel combination of capacitor
C1 and the network formed by the series connection of R1 and
C2. C1 is primarily the pin capacitance. R1 is typically 3250
and is a lumped component made up of some serial resistors
and the on resistance of the switches. C2 is typically 60 pF and
is mainly the ADC sampling capacitor. During the conversion
phase, where the switches are opened, the input impedance is
limited to C1. R1 and C2 make a 1-pole low-pass filter that
reduces undesirable aliasing effect and limits the noise.
When the source impedance of the driving circuit is low, the
AD7661 can be driven directly. Large source impedances will
significantly affect the ac performance, especially total
harmonic distortion (THD). The maximum source impedance
depends on the amount of THD that can be tolerated. The THD
degrades as a function of the source impedance and the
maximum input frequency, as shown in Figure 29.
–105
–100
–95
–90
–85
–80
–75
–70
THD
(dB)
1
10
100
INPUT FREQUENCY (kHz)
03033-0-043
RS = 500
RS = 100
RS = 50
RS = 20
Figure 29. THD vs. Analog Input Frequency and Source Resistance
Driver Amplifier Choice
Although the AD7661 is easy to drive, the driver amplifier
needs to meet the following requirements:
The driver amplifier and the AD7661 analog input circuit
must be able to settle for a full-scale step of the capacitor
array at a 16-bit level (0.0015%). In the amplifier’s data
sheet, settling at 0.1% to 0.01% is more commonly speci-
fied. This could differ significantly from the settling time at
a 16-bit level and should be verified prior to driver
selection. The tiny op amp OP184, which combines ultra
low noise and high gain-bandwidth, meets this settling
time requirement.
相關PDF資料 |
PDF描述 |
|---|---|
| DK-START-5AGXB3NES | ARRIA V STARTER KIT |
| 0210391034 | CABLE JUMPER 1MM .076M 33POS |
| MLG1005S75NJ | INDUCTOR MULTILAYER 75NH 0402 |
| EVAL-AD7652CBZ | BOARD EVALUATION FOR AD7652 |
| EVAL-AD7660CBZ | BOARD EVALUATION FOR AD7660 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7661EDZ | 功能描述:BOARD EVAL FOR AD7661 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7662CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Evaluation Board AD766X/AD767X |
| EVAL-AD7663CB | 制造商:Analog Devices 功能描述: |
| EVAL-AD7663CBZ | 功能描述:BOARD EVALUATION FOR AD7663 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7663EDZ | 制造商:Analog Devices 功能描述:CONVERTER - ADC |
發布緊急采購，3分鐘左右您將得到回復。