參數資料
型號： EVAL-AD5780SDZ
廠商： Analog Devices Inc
文件頁數： 11/28頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR AD5780
設計資源： CN-0200 Circuit
標準包裝： 1
DAC 的數量： 1
位數： 18
數據接口： DSP，MICROWIRE?，QSPI?，和 SPI?
設置時間： 2.5µs
DAC 型： 電壓
工作溫度： -40°C ~ 125°C
已供物品： 板，纜線，CD
已用 IC / 零件： AD5780
相關產品： AD5780ACPZ-ND - IC DAC VOLT OUT 18BIT 24LFCSP
Data Sheet
AD5780
Rev. E | Page 19 of 28
Standalone Operation
The serial interface works with both a continuous and noncon-
tinuous serial clock. A continuous SCLK source can be used
only if SYNC is held low for the correct number of clock cycles.
In gated clock mode, a burst clock containing the exact number
of clock cycles must be used, and SYNC must be taken high after
the final clock to latch the data. The first falling edge of SYNC
starts the write cycle. Exactly 24 falling clock edges must be
applied to SCLK before SYNC is brought high again. If SYNC is
brought high before the 24th falling SCLK edge, the data written
is invalid. If more than 24 falling SCLK edges are applied before
SYNC is brought high, the input data is also invalid.
The input shift register is updated on the rising edge of SYNC.
For another serial transfer to take place, SYNC must be brought
low again. After the end of the serial data transfer, data is
automatically transferred from the input shift register to the
addressed register. When the write cycle is complete, the output
can be updated by taking LDAC low while SYNC is high.
Readback
The contents of all the on-chip registers can be read back via
the SDO pin. Table 7 outlines how the registers are decoded.
After a register has been addressed for a read, the next 24 clock
cycles clock the data out on the SDO pin. The clocks must be
applied while SYNC is low. When SYNC is returned high, the
SDO pin is placed in tristate. For a read of a single register, the
NOP function can be used to clock out the data. Alternatively,
if more than one register is to be read, the data of the first
register to be addressed can be clocked out at the same time
that the second register to be read is being addressed. The SDO
pin must be enabled to complete a readback operation. The
SDO pin is enabled by default.
HARDWARE CONTROL PINS
Load DAC Function (LDAC)
After data has been transferred into the input register of the
DAC, there are two ways to update the DAC register and DAC
output. Depending on the status of both SYNC and LDAC, one
of two update modes is selected: synchronous DAC update or
asynchronous DAC update.
Synchronous DAC Update
In this mode, LDAC is held low while data is being clocked into
the input shift register. The DAC output is updated on the rising
edge of SYNC.
Asynchronous DAC Update
In this mode, LDAC is held high while data is being clocked
into the input shift register. The DAC output is asynchronously
updated by taking LDAC low after SYNC has been taken high.
The update now occurs on the falling edge of LDAC.
Reset Function (RESET)
The AD5780 can be reset to its power-on state by two means:
either by asserting the RESET pin or by using the reset function
in the software control register (see Table 13). If the RESET pin
is not used, hardwire it to IOVCC.
Asynchronous Clear Function (CLR)
The CLR pin is an active low clear that allows the output to be
cleared to a user defined value. The 18-bit clearcode value is
programmed to the clearcode register (see Table 12). It is
necessary to maintain CLR low for a minimum amount of time
to complete the operation (see Figure 2). When the CLR signal
is returned high, the output remains at the clear value (if LDAC
is high) until a new value is loaded to the DAC register. The
output cannot be updated with a new value while the CLR pin is
low. A clear operation can also be performed by setting the CLR
bit in the software control register (see Table 13).
ON-CHIP REGISTERS
DAC Register
Table 9 outlines how data is written to and read from the DAC
register.
The following equation describes the ideal transfer function of
the DAC:
(
)
REFN
REFP
OUT
V
D
V
+
×
=
18
2
where:
VREFN is the negative voltage applied at the VREFN input pin.
VREFP is the positive voltage applied at the VREFP input pin.
D is the 18-bit code programmed to the DAC.
相關PDF資料
PDF描述
GEC25DRAS CONN EDGECARD 50POS R/A .100 SLD
V24C5E125BG CONVERTER MOD DC/DC 5V 125W
GBC18DRAS CONN EDGECARD 36POS R/A .100 SLD
HCC10DREN-S13 CONN EDGECARD 20POS .100 EXTEND
V24C5E125BF2 CONVERTER MOD DC/DC 5V 125W
相關代理商/技術參數
參數描述
EVAL-AD5781SDZ 功能描述:BOARD EVAL FOR AD5781 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5790SDZ 制造商:Analog Devices 功能描述:AD5790 DAC EVALUATION BOARD 制造商:Analog Devices 功能描述:AD5790, DAC, EVALUATION BOARD 制造商:Analog Devices 功能描述:AD5790, DAC, EVALUATION BOARD, Silicon Manufacturer:Analog Devices, Silicon Core 制造商:Analog Devices 功能描述:AD5790, DAC, EVALUATION BOARD, Silicon Manufacturer:Analog Devices, Silicon Core Number:(Not Applicable), Kit Application Type:(Not Available), Application Sub Type:DAC, Features:20-bit Voltage Output DAC, Integrated Precision , RoHS Compliant: Yes
EVAL-AD5791SDZ 功能描述:BOARD EVAL FOR AD5791 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5821AEBZ 功能描述:BOARD EVAL FOR AD5821 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5821EBZ 功能描述:BOARD EVALUATION FOR AD5821 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*