參數資料
型號： EVAL-AD5522EBDZ
廠商： Analog Devices Inc
文件頁數： 25/64頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR 14X14MM AD5522
標準包裝： 1
主要目的： 測試與測量，參數測量單元（PMU）
已用 IC / 零件： AD5522
已供物品： 板
Data Sheet
AD5522
Rev. E | Page 31 of 64
When the AD5522 is placed in high-Z mode, the clamp circuit
is always configured to monitor the measure current signal
(irrespective of which high-Z mode is selected, high-Z V or
high-Z I). At this time, the clamp circuit is also comparing to
the voltage clamp levels. Because the device is in high-Z mode,
the measure current signal is at zero, but zero for the measure
current is always the VMID voltage set by the offset DAC. For
default offset DAC conditions, this causes no concern. For other
settings of the offset DAC, the zero point follows the VMID,
and as the clamp circuit is comparing the voltage clamp levels
to the measure current signal, there may be instances where
the voltage clamp levels cause the alarm to flag during high-Z
mode. To avoid this, the clamps can be disabled when going
into high-Z mode.
CURRENT RANGE SELECTION
Integrated thin film resistors minimize the need for external
components and allow easy selection of any of these current
ranges: ±5 A (200 kΩ), ±20 μA (50 kΩ), ±200 μA (5 kΩ), and
±2 mA (500 Ω). One current range up to ±80 mA can be
accommodated per channel by connecting an external sense
resistor. For current ranges in excess of ±80 mA, it is necessary
that an external amplifier be used.
For the suggested current ranges, the maximum voltage drop
across the sense resistors is ±1 V. However, to allow for error
correction, there is some overrange available in the current
ranges (±12.5% or ±0.125 V across RSENSE). The full-scale
voltage range that can be loaded to the FIN DAC is ±11.5 V;
the forced current can be calculated as follows:
FI = 4.5 × VREF × ((DAC_CODE 32,768)/216)/(RSENSE ×
MI_Amplifier_Gain)
where:
FI is the forced current.
RSENSE is the selected sense resistor.
MI_Amplifier_Gain is the gain of the measure current
instrumentation amplifier. This gain can be set to 5 or 10
via the serial interface.
In the ±200 μA range with the 5 kΩ sense resistor and an ISENSE
gain of 10, the maximum current range possible is ±225 μA.
Similarly, for the other current ranges, there is an overrange of
12.5% to allow for error correction.
Also, the forced current range is the quoted full-scale range only
with an applied reference of 5 V or 2.5 V (with ISENSE amplifier
gain = 5). The ISENSE amplifier is biased by the VMID DAC
voltage in such a way as to center the measure current output
irrespective of the voltage span used.
When using the EXTFOHx outputs for current ranges up to
±80 mA, there is no switch in series with the EXTFOHx line,
ensuring minimum capacitance present at the output of the
force amplifier. This feature is important when using a pin
electronics driver to provide high current ranges.
HIGH CURRENT RANGES
With the use of an external high current amplifier, one high
current range in excess of ±80 mA is possible. The high current
amplifier buffers the force output and provides the drive for the
required current.
To eliminate any timing concerns when switching between the
internal ranges and the external high current range, there is a
mode where the internal ±80 mA stage can be enabled at all
times. See Table 26 for more information.
DUTGND
MEASVHx
DUT
RSENSE
EXTMEASIHx
EXTMEASILx
FOHx
EXTFOHx
HIGH
CURRENT
AMPLIFIER
CFFx
FIN
INTERNAL RANGE SELECT
(±5A, ±20A, ±200A, ±2mA)
DAC
–
+
–
+
×5 or ×10
×1
AGND
MEASOUTx
×1 OR
×0.2
4k
2k
VMID TO
CENTER
I RANGE
4k
EN
06197-
028
Figure 47. Addition of High Current Amplifier for Wider Current Range (>±80 mA)
相關PDF資料
PDF描述
EVAL-AD5520EBZ BOARD EVAL FOR AD5520
MAX6198AESA+T IC VREF SERIES PREC 4.096V 8SOIC
QPI-5-EVAL1 EVALUATION BOARD FOR QPI-5
H6MMH-4006M DIP CABLE - HDM40H/AE40M/HDM40H
QPO-2-EVAL1 EVALUATION BOARD FOR QPO-2
相關代理商/技術參數
參數描述
EVAL-AD5522EBUZ 功能描述:BOARD EVAL FOR 12X12MM AD5522 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-AD5532EB 制造商:AD 制造商全稱:Analog Devices 功能描述:32-Channel Infinite Sample-and-Hold
EVAL-AD5532EBZ 功能描述:BOARD EVAL FOR AD5532 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5532HSEBZ 功能描述:BOARD EVAL FOR AD5532HS RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5533EB 制造商:AD 制造商全稱:Analog Devices 功能描述:32-Channel Precision Infinite Sample-and-Hold
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*