參數資料
型號： EVAL-AD5252EBZ
廠商： Analog Devices Inc
文件頁數： 16/28頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD5252
標準包裝： 1
主要目的： 數字電位器
已用 IC / 零件： AD5252
主要屬性： 2 通道，256 位置
次要屬性： I²C 接口
已供物品： 板
Data Sheet
AD5251/AD5252
Rev. D | Page 23 of 28
LAYOUT AND POWER SUPPLY BIASING
It is always a good practice to employ a compact, minimum
lead-length layout design. The leads to the input should be as
direct as possible, with a minimum conductor length. Ground
paths should have low resistance and low inductance.
Similarly, it is also good practice to bypass the power supplies
with quality capacitors. Low equivalent series resistance (ESR)
1 μF to 10 μF tantalum or electrolytic capacitors should be
applied at the supplies to minimize any transient disturbance
and filter low frequency ripple. Figure 39 illustrates the basic
supply-bypassing configuration for the AD5251/AD5252.
VDD
VSS
GND
C3
AD5251/AD5252
C4
C1
+
C2
10
F
10
F
0.1
F
0.1
F
03823-0-039
Figure 39. Power Supply-Bypassing Configuration
The ground pin of the AD5251/AD5252 is used primarily as a
digital ground reference. To minimize the digital ground
bounce, the AD5251/AD5252 ground terminal should be joined
remotely to the common ground (see Figure 39).
DIGITAL POTENTIOMETER OPERATION
The structure of the RDAC is designed to emulate the
performance of a mechanical potentiometer. The RDAC
contains a string of resistor segments with an array of analog
switches that act as the wiper connection to the resistor array.
The number of points is the resolution of the device. For
example, the AD5251/AD5252 emulate 64/256 connection
points with 64/256 equal resistance, RS, allowing them to
provide better than 1.5%/0.4% resolution.
Figure 40 provides an equivalent diagram of the connections
between the three terminals that make up one channel of the
RDAC. Switches SWA and SWB are always on, but only one of
switches SW(0) to SW(2N – 1) can be on at a time (determined by
the setting decoded from the data bit). Because the switches are
nonideal, there is a 75 Ω wiper resistance, RW. Wiper resistance
is a function of supply voltage and temperature: Lower supply
voltages and higher temperatures result in higher wiper
resistances. Consideration of wiper resistance dynamics is
important in applications in which accurate prediction of
output resistance is required.
SWB
SW(1)
SW(0)
BX
RS
SWA
SW(2N – 1)
AX
WX
SW(2N – 2)
RDAC
WIPER
REGISTER
AND
DECODER
RS = RAB/2N
RS
DIGITAL
CIRCUITRY
OMITTED FOR
CLARITY
03823-0-040
Figure 40. Equivalent RDAC Structure
PROGRAMMABLE RHEOSTAT OPERATION
If either the W-to-B or W-to-A terminal is used as a variable
resistor, the unused terminal can be opened or shorted with W;
such operation is called rheostat mode (see Figure 41). The
resistance tolerance can range ±20%.
A
W
B
03823-0-041
A
W
B
A
W
B
Figure 41. Rheostat Mode Configuration
The nominal resistance of the AD5251/AD5252 has 64/256
contact points accessed by the wiper terminal, plus the B terminal
contact. The 6-/8-bit data-word in the RDAC register is decoded
to select one of the 64/256 settings. The wiper’s first connection
starts at the B terminal for Data 0x00. This B terminal connection
has a wiper contact resistance, RW, of 75 Ω, regardless of the
nominal resistance. The second connection (the AD5251 10 kΩ
part) is the first tap point where RWB = 231 Ω (RWB = RAB/64 +
RW = 156 Ω + 75 Ω) for Data 0x01, and so on. Each LSB data
value increase moves the wiper up the resistor ladder until the
last tap point is reached at RWB = 9893 Ω. See Figure 40 for a
simplified diagram of the equivalent RDAC circuit.
The general equation that determines the digitally programmed
output resistance between W and B is
AD5251: RWB(D) = (D/64) × RAB + 75 Ω
(1)
AD5252: RWB(D) = (D/256) × RAB + 75 Ω
(2)
where:
D is the decimal equivalent of the data contained in the
RDAC latch.
RAB is the nominal end-to-end resistance.
相關PDF資料
PDF描述
101-0452 KIT DEV RABBIT RCM2100 INTL
VE-J7X-EZ-F1 CONVERTER MOD DC/DC 5.2V 25W
EVAL-ADF4360-8EBZ1 BOARD EVALUATION FOR ADF4360-8
VE-J7X-EY-S CONVERTER MOD DC/DC 5.2V 50W
MCP73213-B6SI/MF IC LI-ION/LI-POLY CTRLR 10-DFN
相關代理商/技術參數
參數描述
EVAL-AD5252SDZ 功能描述:BOARD EVAL FOR AD5252 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-AD5254EBZ 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits)
EVAL-AD5254SDZ 功能描述:BOARD EVAL FOR AD5254 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-AD5258DBZ 功能描述:BOARD EVAL FOR AD5258DBZ RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-AD5259DBZ 功能描述:BOARD EVAL FOR AD5259DBZ RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*