參數資料
型號： EVAL-AD1940AZ
廠商： Analog Devices Inc
文件頁數： 4/36頁
文件大?。?/td> 0K
描述： BOARD EVAL AD1940 SIGMADSP
標準包裝： 1
系列： SigmaDSP®
主要目的： 音頻，音頻處理
嵌入式： 是，DSP
已用 IC / 零件： AD1940
主要屬性： 單芯片多通道 28/56 位音頻 DSP
次要屬性： 均衡，交叉，低音增強，多頻帶動態處理，延遲等
已供物品： 板
AD1940/AD1941
Rev. B | Page 12 of
36
PIN FUNCTIONS
Table 10 shows the AD1940/AD1941’s pin numbers, names, and
functions. Input pins have a logic threshold compatible with
TTL input levels and may be used in systems with 3.3 V or
5 V logic.
SDATA_IN0
SDATA_IN1
SDATA_IN2/TDM_IN1
SDATA_IN3/TDM_IN0
Serial Data/TDM Inputs. The serial format is selected by
writing to Bits 2:0 of the serial input port control register.
SDATA_IN2 and SDATA_IN3 are dual-function pins that can
be set to a variety of standard 2-channel formats or to TDM
mode. Two of these four pins (SDATA_IN2 and SDATA_IN3)
can be used as TDM inputs in either dual-wire 8-channel mode
or single-wire 16-channel mode (TDM_O0 only). In dual-wire
8-channel mode, Channels 0 to 7 are input on SDATA_IN3 and
Channels 8 to 15 on SDATA_IN2. In single-wire 16-channel
mode, Channels 0 to 15 are input on SDATA_IN2. See the
Serial Data Input/Output Ports section for further explanation.
LRCLK_IN
BCLK_IN
Left/Right and Bit Clocks for Timing the Input Data. These
input clocks are associated with the SDATA_IN0 through
SDATA_IN3 signals. The input port is always in a slave
configuration. These pins also function as frame sync and bit
clock for the input TDM stream.
SDATA_OUT0/TDM_O0
SDATA_OUT1
SDATA_OUT2
SDATA_OUT3
SDATA_OUT4/TDM_O1
SDATA_OUT5
SDATA_OUT6
SDATA_OUT7/DCSOUT
Serial Data/TDM/Data Capture Outputs. These pins are used
for serial digital outputs. For non-TDM systems, these eight
pins can output 16 channels of digital audio, using a variety of
standard 2-channel formats. They are grouped into two groups
of four pins (Pins 0 to 3 and Pins 4 to 7); each group can be
independently set to any of the available serial modes, allowing
the AD1940/AD1941 to simultaneously communicate with two
external devices with different serial formats. Two of these eight
pins (SDATA_OUT0 and SDATA_OUT4) can be used as TDM
outputs in either dual-wire 8-channel mode or single-wire 16-
channel mode (TDM_OUT0 only). In dual-wire 8-channel
mode, Channels 0 to 7 are output on SDATA_OUT0 and
Channels 8 to 15 on SDATA_OUT4. See the Serial Data
Input/Output Ports section for further explanation.
SDATA_OUT7 can also be used as a data capture output, as
described in the Data Capture Registers section.
LRCLK_OUT0
BCLK_OUT0
Output Clocks. This clock pair is used for outputs
SDATA_OUT0 through SDATA_OUT3. In slave mode, these
clocks are inputs to the AD1940/AD1941. On power-up, these
pins are set to slave mode to avoid conflicts with external
master mode devices.
LRCLK_OUT1
BCLK_OUT1
Output Clocks. This clock pair is used for outputs
SDATA_OUT4 through SDATA_OUT7. In slave mode, these
clocks are inputs to the AD1940/AD1941. On power-up, these
pins are set to slave mode to avoid conflicts with external
master mode devices.
MCLK
Master Clock Input. The AD1940/AD1941 uses a PLL to
generate the appropriate internal clock for the DSP core. An
in-depth description of using the PLL is found in the Setting
PLL_CTRL0
PLL_CTRL1
PLL_CTRL2
PLL Mode Control Pins. The functionality of these pins is
described in the Setting Master Clock/PLL Mode section.
CDATA (AD1940)
Serial Data Input for the SPI Control Port.
COUT (AD1940)
Serial Data Output for the SPI Port. This is used for reading
back registers and memory locations. It is three-stated when an
SPI read is not active.
CCLK (AD1940)
SPI Bit Clock. This clock may either run continuously or be
gated off between SPI transactions.
CLATCH (AD1940)
SPI Latch Signal. This must go low at the beginning of an SPI
transaction and high at the end of a transaction. Each SPI
transaction may take a different number of CCLKs to complete,
depending on the address and read/write bit that are sent at the
beginning of the SPI transaction.
SCL (AD1941)
I2C Clock. This pin is always an input because the AD1941
cannot act as a master on the I2C bus. The line connected to this
pin should have a 2 kΩ pull-up resistor on it.
SDA (AD1941)
I2C Serial Data. The data line is bidirectional. The line
connected to this pin should have a 2 kΩ pull-up resistor on it.
相關PDF資料
PDF描述
6278128-6 MT-RJ/MT-RJ 6M1 C/A
1-1906054-0 CA 2MM OFNR 62.5/125,LC SEC GRE
M3DRK-1006J IDC CABLE - MKR10K/MC10G/MPR10K
VE-20J-EX CONVERTER MOD DC/DC 36V 75W
RNF-100-1-GY-SP HEAT SHRINK TUBING
相關代理商/技術參數
參數描述
EVAL-AD1940EB 制造商:Analog Devices 功能描述:DEV TOOLS, SIGMADSPTM MULTICH 28BIT AUD PROCESSOR - Bulk
EVAL-AD1940MINIB 制造商:Analog Devices 功能描述:SIGMADSP EVAL BD - Bulk 制造商:Rochester Electronics LLC 功能描述:
EVAL-AD1940MINIBZ 功能描述:BOARD EVAL AD1940 MINI SIGMADSP RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:SigmaDSP® 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
EVAL-AD1941EB 制造商:Analog Devices 功能描述:EVAL BD SIGMADSPMULTICHANAUDIO PROCESSOR - Bulk
EVAL-AD1953EB 制造商:Analog Devices 功能描述:EVAL BRD FOR 3 CH 24 BIT SIG-PROCESS DAC - Bulk 制造商:Analog Devices 功能描述:EVALUATION KIT ((NS))
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*