- 您現在的位置：買賣IC網 > PDF目錄16561 > EV-ADF4360-0EB1Z (Analog Devices Inc)BOARD EVAL FOR ADF4360-0 PDF資料下載
參數資料
| 型號： | EV-ADF4360-0EB1Z |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADF4360-0 |
| 標準包裝： | 1 |
| 主要目的： | 計時，頻率合成器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADF4360-0 |
| 主要屬性： | 帶 VCO 的單路整數-N PLL |
| 次要屬性： | 2.5GHz，200kHz PFD |
| 已供物品： | 板，纜線，CD |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
ADF4360-0
Data Sheet
Rev. C | Page 10 of 24
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF4360 family allows the user
to access various internal points on the chip. The state of
MUXOUT is controlled by M3, M2, and M1 in the function
latch. The full truth table is shown in Table 7. Figure 13 shows
the MUXOUT section in block diagram form.
Lock Detect
MUXOUT can be programmed for two types of lock detect:
digital and analog. Digital lock detect is active high. When LDP
in the R counter latch is set to 0, digital lock detect is set high
when the phase error on three consecutive phase detector cycles
is less than 15 ns.
With LDP set to 1, five consecutive cycles of less than 15 ns
phase error are required to set the lock detect. It stays set high
until a phase error of greater than 25 ns is detected on any sub-
sequent PD cycle.
The N-channel open-drain analog lock detect should be operat-
ed with an external pull-up resistor of 10 k nominal. When a
lock has been detected, this output is high with narrow low-
going pulses.
R COUNTER OUTPUT
N COUNTER OUTPUT
DIGITAL LOCK DETECT
DGND
CONTROL
MUX
MUXOUT
DVDD
ANALOG LOCK DETECT
SDOUT
04644-013
Figure 13. MUXOUT Circuit
INPUT SHIFT REGISTER
The ADF4360 family’s digital section includes a 24-bit input
shift register, a 14-bit R counter, and an 18-bit N counter,
comprised of a 5-bit A counter and a 13-bit B counter. Data is
clocked into the 24-bit shift register on each rising edge of CLK.
The data is clocked in MSB first. Data is transferred from the
shift register to one of four latches on the rising edge of LE. The
destination latch is determined by the state of the two control
bits (C2, C1) in the shift register. These are the two LSBs, DB1
and DB0, as shown in Figure 2.
The truth table for these bits is shown in Table 5. Table 6 shows
a summary of how the latches are programmed. Note that the
test mode latch is used for factory testing and should not be
programmed by the user.
Table 5. C2 and C1 Truth Table
Control Bits
Data Latch
C2
C1
0
Control Latch
0
1
R Counter
1
0
N Counter (A and B)
1
Test Mode Latch
VCO
The VCO core in the ADF4360 family uses eight overlapping
bands, as shown in Figure 14, to allow a wide frequency range
to be covered without a large VCO sensitivity (KV) and resultant
poor phase noise and spurious performance.
The correct band is chosen automatically by the band select
logic at power-up or whenever the N counter latch is updated. It
is important that the correct write sequence be followed at pow-
er-up. This sequence is
1. R counter latch
2. Control latch
3. N counter latch
During band select, which takes five PFD cycles, the VCO VTUNE
is disconnected from the output of the loop filter and connected
to an internal reference voltage.
04644-014
0.5
0.7
0.9
1.1
1.3
1.5
1.9
2.1
2.3
1.7
2.5
VOLTAGE
(V)
FREQUENCY (MHz)
2200
2400
2600
2800
3000
Figure 14. Frequency vs. VTUNE, ADF4360-0
The R counter output is used as the clock for the band select logic
and should not exceed 1 MHz. A programmable divider is provid-
ed at the R counter input to allow division by 1, 2, 4, or 8 and is
controlled by Bits BSC1 and BSC2 in the R counter latch. Where
the required PFD frequency exceeds 1 MHz, the divide ratio should
be set to allow enough time for correct band selection.
After band select, normal PLL action resumes. The nominal
value of KV is 56 MHz/V or 28 MHz/V, if divide-by-2 operation
has been selected (by programming DIV2 [DB22] high in the N
counter latch). The ADF4360 family contains linearization cir-
cuitry to minimize any variation of the product of ICP and KV.
相關PDF資料 |
PDF描述 |
|---|---|
| H3DKH-2618M | IDC CABLE - HKR26H/AE26M/HPK26H |
| M3TTK-1020K | IDC CABLE - MSD10K/MC10F/MSD10K |
| AK669-30-R | CABLE USB V1.1 EXTENSION 3M |
| REC5-2415DRWZ/H6/C | CONV DC/DC 5W 9-36VIN +/-15VOUT |
| EV-ADF4360-1EB1Z | BOARD EVAL FOR ADF4360-1 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EV-ADF4360-1EB1Z | 功能描述:BOARD EVAL FOR ADF4360-1 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EV-ADF4360-2EB1Z | 功能描述:時鐘和定時器開發工具 Evaluation Board I.C. RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V |
| EV-ADF4360-3EB1Z | 功能描述:BOARD EVAL FOR ADF4360-3 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EV-ADF4360-4EB1Z | 功能描述:BOARD EVAL FOR ADF4360-4 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| EV-ADF4360-5EB1Z | 功能描述:時鐘和定時器開發工具 Evaluation Board I.C. RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。